Next Article in Journal
Development of an Integrated Water Resource Scheduling Model Based on Platform Plug-In: A Case Study of the Wudu Diversion and Irrigation Area, China
Next Article in Special Issue
Sequential Nitrification—Autotrophic Denitrification Using Sulfur as an Electron Donor and Chilean Zeolite as Microbial Support
Previous Article in Journal
Reliability of a Contamination-Detection Sensor Network in Water Distribution Systems during a Cyber-Physical Attack
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Removal of N and P in a Rotating Biological Contactor Plant: Case Study Agnita, Romania

1
Faculty of Agriculture Sciences, Food Industry and Environmental Protection, Lucian Blaga University of Sibiu, 550024 Sibiu, Romania
2
S.C. Apa Tarnavei Mari S.A., 551130 Medias, Romania
3
Mures River Catchment Administration, 540057 Târgu Mureș, Romania
*
Author to whom correspondence should be addressed.
Water 2022, 14(22), 3670; https://doi.org/10.3390/w14223670
Submission received: 17 October 2022 / Revised: 9 November 2022 / Accepted: 11 November 2022 / Published: 14 November 2022

Abstract

:
The wastewater treatment plant of Agnita, Romania was designed with a rotational biological contactor system for a population of approximately 9500, but for environmental protection reasons it must comply with regulations concerning nitrogen and phosphorus designed for larger communities. In order to achieve the prescribed limits for these pollutants, we have used a 40% FeCl3 solution, continuously added to the distributor, without changes in flow or equipment. Its use boosts the removal of ammonia nitrogen, and phosphorus, bringing them within the limits and with reasonable cost. To determine the ferric chloride to be used we considered, aside from the pollutant load, the water temperature, and introduced a new parameter: specific removal power that enabled us to optimize the volume of FeCl3. A major contribution to nitrogen removal was achieved by the denitrification bacteria favored by the presence of ferric ions, which also precipitate phosphorus. The results of this study, performed since September 2021, enable us to continue to use this method and enlarge its application to other plants owned by the local operator.

1. Introduction

To demonstrate the importance of clean water in the 21st century, for mankind and nature, is almost a tautology due to mankind’s awareness and the huge number of norms, regulations, and papers on this theme [1], but efforts are still needed to keep waters clean. Regulators all over the world have issued norms and standards for water quality, and in Europe they are grouped under the umbrella of Council Directive 91/271/EEC [2] with its multiple amendments; in Romania it is implemented by the new Law of the Environment [3], also with multiple amendments and subsequent norms for wastewater treatment [4,5], which include permitted concentrations when using wastewater treatment plants (WWTPs) [6], as well as the disposal of the resulting sludge [7].
There are multiple ways of treating wastewater [1]. The core of each plant is the biological reactor, which mainly converts organic pollutants into harmless compounds, usually found in sewage sludge [8]. Each approach has its advantages and disadvantages in terms of cost and efficiency [9,10].
Among the possibilities for treating wastewater, rotating biological contactors (RBCs) are used mainly for communities with population equivalents (PEs) ranging from 100 to 10,000, but they can also be used for treating several million liters per day [11,12].
For communities larger than 1000 inhabitants modular RBCs are used [13], which consist of several modules of biodiscs that usually work in parallel.
The efficiency of primary pollutant removal, expressed as biological oxygen demand (BOD), chemical oxygen demand (COD), and total suspended solids (TSS), depends on the ability to provide oxygen to the active microorganisms (aeration). In RBCs, the oxygen transfer is achieved using cyclical air exposure and renewal of the air–water interfaces (biofilm), as well as by water trickling back into the tank [14].
Disc rotation mixes the liquid and in addition to oxygen provides the nutrients for the development of the microorganisms that form the biofilm as well as breaking the biofilm due to friction, thus resulting in sludge [15].
The advantages of RBCs compared to activated sludge (aeration) equipment are: small space requirement, simple monitoring and process control, low operational and maintenance costs, high biomass concentration, low excess sludge production, short hydraulic retention time, high oxygen transfer efficiency, no need for sludge recirculation, resistance to shock and toxic loads, and compact design [16].
Usually, RBCs are used in communities with less than 10,000 PE, so, at least in Europe, these WWTPs are not required to comply with regulations regarding the maximum permitted values for nitrogen and phosphorus. The removal of these two pollutants can easily be achieved in conventional activated sludge plants, where anoxic zones can be designed and operated [17], but in typical RBCs, achieving this is more complicated, although on the same disc nitrifying (aerobic) Betaproteobacteria Nitrosomonas and Nitrospira [18] can coexist with anaerobic ones at the contact zone with the water, closer to the disc surface [19,20]. Regarding the populations of anaerobic microorganisms, the literature presents many species and genera, depending on the type of wastewater and environmental conditions [21]: Comamonas denitrificans [22,23], Acinetobacter sp., Bacillus sp., Diaphorobacter sp., Pseudomonas sp., Rhodococcus sp., Zobellella sp. [24], Tetrasphaera (which besides denitrification is also a good phosphate remover) [25], Riemeralla sp., Parabacterioides sp., Candidatus, Accumulibacter phosphatis [26], Thauera sp., and Paracoccus sp. [27].
Among the best technologies used for nitrogen removal are: moving bed biofilm reactors (MBBRs), moving bed biofilm reactor-membrane bioreactors (MBBR-MBRs), moving bed membrane bioreactors (MB-MBRs) and the integrated fixed-film activated sludge (IFAS) process [28,29,30,31]. Recently, a novel technology—anaerobic membrane bioreactors (AnMBRs)—has gained momentum, with good results in nitrogen removal [32,33].
For the improvement of N removal in RBCs, special techniques and equipment were conceived, i.e., submerged discs [34,35], transformation into an electrochemical reactor with heterotrophic–autotrophic denitrification [36], Donnan dialysis [37], or the use of certain microorganisms, such as the mixotrophic Paracoccus denitrificans that can undertake simultaneous aerobic carbon oxidation, nitrification, and denitrification [38], or other autotrophic microorganisms [16]. Good results in denitrification within RBCs have been demonstrated by processes like anaerobic ammonium oxidation (AnAmmOx) coupled with nitrite reduction and denitrifying anaerobic methane oxidation (DAMO) [17].
Regardless of the biological reactor type, a WWTP is a “captive customer” having almost no means to control the influent, which continuously changes day by day and even hour by hour. On the other hand, strictly regulated effluent parameters require a thorough operation of the plant, with reduced costs. Thus, the operators are supposed to maintain the plant in continuous function and, if possible, to improve its economic and environmental efficiency, and this is what we have tried at Agnita.

2. Materials and Methods

The town of Agnita is situated in the middle of Romania (Sibiu County), on the banks of the Hartibaciu River, at an altitude of 490 m (GPS coordinates 45°58′23″ N, 24°37′2″ E), with a population of 8732 inhabitants according to the 2011 census, a decrease from the 2002 census value of 10,894.
For environmental protection, and in accordance with European and Romanian laws, in 2010 the design and construction of a new WWTP started on behalf of the local operator, Apa Tarnavei Mari S.A. (English: Water of Tarnava Mare River Co.) in Medias. The plant was planned for 9500 PE, on the right bank of the Hartibaciu, at the southwestern town limits, and was commissioned in June 2014. From the very beginning, the WWTP was equipped with a supervisory control and data acquisition (SCADA) system that monitors the main parameters and acts accordingly.
The only major non-residential wastewater generators are a company manufacturing charging cables and solenoid systems, a producer of wood parquet flooring, and the city hospital. Their average cumulative outflow is 64.8 m3/day (2000 m3/month), which is less than 7% of the treated wastewater (data not shown). According to the reports, only the wastewater generated by the hospital sometimes exceeds the maximal permitted limits for BOD and nitrogen, but the situation is known, and it will be remediated.
The main parameters for the design and operation of the WWTP were:
  • Daily average inflow: 2607 m3 (dry weather);
  • Daily maximal inflow: 2971 m3 (35 L/s);
  • Q max during rain: 540 m3/h (150 L/s);
For planning the multi-annual inflow, concentration and load values were considered. Their mean values [39] are shown in Table 1.
The schematic flow of this WWTP is presented in Figure 1.
Sewage water is pumped into the WWTP and then it flows gravitationally until it is discharged in the Hartibaciu River.
The screen, the sand and fat remover, and the primary clarifier act as mixers and buffers, hence the load (concentration × flow) of the water entering the RBCs is quite constant over time.
The FeCl3 solution is added before distribution; it then enters the biodiscs, which have the main characteristics presented in Table 2.
The rotation speed was set after multiple tests at 2 min−1, less than in other cases [40].
Considering the multi-annual data, the minimal water temperature during the plant operation was 10 °C, which during the years of operation was reached only in very few and short periods. In the RBC biofilm, the metabolic processes are less temperature-dependent than in activated sludge, one reason being the polycarbonate casing that provides some thermal insulation. The RBCs of Agnita are presented in Figure 2.
From the secondary clarifier, the treated water is discharged into the Hartibaciu River, while the resulting wet sludge is pumped onto the sludge-reed (genus Phragmites) beds, a simple and cost-effective dehydration process (air-drying) [41]. Reeds have an active growth and use the sludge nutrients and water; the resulting biomass is harvested every year and used for composting.

Analysis

The analyses performed in the WWTP are the usual ones. The standards in force according to the requirements and the authorization issued by the Olt River Catchment Administration No. 43 of 13 May 2020 (and those before it) for determination of the main parameters, the equipment, and the method as well as the maximal permitted limits (MPLs) (as daily averages) are presented in Table 3. All values are the mean of three determinations.
The morphological cluster analysis and identification of aerobic and anaerobic microorganisms were performed with an Olympus BX40 microscope (Olympus Corporation, Shinjuku City, Tokyo) with a digital camera and phase contrast, as prescribed by Eikelboom [42]. Both fresh samples and those after Gram staining were observed in a clear field, with 100× magnification [43]. Cluster dimensions and filament thickness were measured using Micro Image 4.0 software.
It is noteworthy that the Olt River Catchment Administration imposed a limit for total nitrogen, although this is not required to be determined by the laws in force; however they argued that the number of inhabitants is close to 10,000, so they applied the precautionary principles for environmental protection. Moreover, in 2022 a national census took place and there is the possibility the population could exceed 10,000 inhabitants, thus driving the town and the WWTP into another category where total phosphorous must be below 2 mg/L [44] and the minimal elimination efficiency, according to the aforementioned norm, has to be 80% for total phosphorus and 70–80% for total nitrogen.
The WWTP operators take samples every day at 8 in the morning from both the influent and the effluent and perform the required analyses, the inflow results being used for setting the operational parameters and the outflow results being reported for the previous day.
Sampling points are placed before the grids and after the secondary settler, where the water flow is measured as well. For operational reasons, there are sampling points after each piece of equipment.
In time, we observed that there are good correlations between the loads of influent ammonia nitrogen (N-NH4+), total nitrogen (total N), and total phosphorus as presented in Supplementary Material S1. Because of this observation, for operational reasons we have decided to calculate the volume of 40% FeCl3 solution to be dripped during the next 24 h considering the (N-NH4+) load in the influent, as it is much simpler and cheaper.
The operator has the possibility of varying the flow of the respective peristaltic pump in case outstanding inflows are presented, exceeding the storage capacity of the primary settler, and thus increasing the flow in the RBC as well. By entering the inflow and the concentration into an Excel form, the total load (for all pollutants, total nitrogen and phosphorus included) as well as the elimination power required for their removal can be calculated.

3. Results and Discussion

The first two years (June 2014–December 2016) were dedicated to testing and fixing the WWTP, to adjust to real work conditions. After this period, noting that the total nitrogen reduction was low and the concentrations were above permitted levels, in January 2017 we decided to add 40% FeCl3 solution, taking into account both the literature [45,46] and the good results we already had at the conventional (with activated sludge) WWTP in Medias [47,48] where, besides coagulation, FeCl3 had been used for phosphorus removal, too. Other reasons we used FeCl3 were because ferric ions, in small amounts, are beneficial for bacterial metabolism [49], as a coagulant, increase the agglomeration and deposition of sludge, and last but not least, because the resulting sewage sludge was to be landfilled on a reed bed, and we did not want the addition of Al in it.
The in- and outflow values allowed us to calculate both the pollutant removal, as the difference between the initial and final loads, and the removal efficiency (RE) with the classical (Equation (1)):
R E = L o a d i n L o a d o u t L o a d i n × 100 ( % )
where:
Loadin = inflow amount of a certain pollutant (COD, BOD, TSS, total N, or Total P) for a certain time period (kg); and
Loadout = outflow amount of the same pollutant for the same period (kg).
The data for the years 2015–2021 are presented in Supplementary Material S2; the removal efficiency is shown in Figure 3.
A good removal efficiency may be seen for COD, BOD, and TSS, and increased efficiency of total nitrogen after the addition of FeCl3 (January 2017). The addition of FeCl3 was beneficial for the removal of phosphorus, which gets closer to the permitted limits, as seen in Table 4.
It may be seen that the addition of FeCl3 improves phosphorus removal, although the effluent concentration is above the MPL. Preliminary tests (data not shown) have proven that the supplementation with 40–50% of the amount of FeCl3 will reduce the effluent concentration below the prescribed values for a WWTP serving more than 10,000 PE, but with higher costs, and so it was decided not to use additional FeCl3.
When performing the microscopic determination of the existing bacterial colonies within the RBC at the laboratory of the Apa Tarnavei Mari Co. in Medias, we found predominantly aerobic microorganisms, responsible for the transformation of ammonia nitrogen into nitrates, as seen in Figure 4.
After the first two years of its commissioning, we also found anaerobic microorganisms in the RBC that transform nitrates into gaseous nitrogen, thus reducing the amount of total nitrogen in the effluent, as seen in Figure 5.
Their presence is beneficial for the WWTP because they provide the release of nitrogen into the air, thus allowing us to achieve the prescribed values for total nitrogen.
When analyzing their distribution, we found (as expected) more nitrifying microorganisms on the external disc surface, while the denitrifying ones were present in the water and near the disc surface.
To determine the efficiency of the major treatment steps for the removal of nitrogen, we measured the values of ammonium and total nitrogen (mean of determinations made every other month) between September 2021 to August 2022 (the period considered in this paper), which are presented in Table 5.
This determination showed that the nitrogen removal takes place mainly in the RBC, but it continues in the secondary settler as well.
Starting in January 2017, the required volume of ferric chloride was divided into three equal portions, all manually added at 8 a.m., 4 p.m., and midnight. This proactive attitude provided the good results presented in Figure 3 and detailed in Supplementary Materials S1 and S2.
In June 2021, we decided not to manually add the coagulant, but automatically, using a dosing system built in-house. The results reflected better compliance with the permitted discharge limits and keeping the amount of FeCl3 within reasonable limits.
It is also noteworthy that since June 2021, the average concentration of FeCl3 in the water was 37.0357 ± 10.098 μM, ten times less than the 400 μM stated by Kim et al. [50] to be toxic for microorganisms (complete data in Supplementary Material S1), thus preventing any “ferric shock”.
The good results after one year of application of this method (September 2021–August 2022), presented in detail in Supplementary Material S1, are very consistent with those of Hassard et al. [16], Ni et al. [17], and Mizyed [20], and are comparable with those of Waquas et al. [51] and Cvetkovic et al. [52].
As expected, a reverse dependency may be seen between the volume of added FeCl3 and water temperature (Figure 6). In the same figure we have also represented the specific removal power for nitrogen, which has a similar rise as the water temperature variation. This is normal because bacterial activity is stimulated by temperature increase [12] and we have already proven this in an activated sludge reactor [45].
Considering that ferric chloride boosts the removal of ammonia nitrogen, total nitrogen, and phosphorus, we introduced a new parameter, specific removal power (SRP), i.e., the volume of 40% FeCl3 required for the elimination of 1 kg of the N or P, defined (Equation (2)) as:
S R P = V F e C l 3 M x
where:
VFeCl3 = the volume of 40% ferric chloride solution (m3);
x = the parameter considered for determination of the SRP (ammonia nitrogen, total N or total P); and
Mx = the total inflow load (kg) for this parameter for a certain time period.
A strong relationship between water temperature and bacterial activity, expressed by nitrogen removal when adding FeCl3, was also observed (Figure 6, right OY axis).
In addition, we noticed that there are similarities between the shapes of the SRP curves (Figure 7).
These similarities will allow us to consider ammonia nitrogen as a control parameter for the future development of an automated continuous dripping system.
When plotting the specific removal powers and water temperature, the results are shown in Figure 8.
When using this concept, the resulting diagrams (Figure 8) more explicitly show the pollutant removal after FeCl3 addition correlated with the inflow load and temperature.
Furthermore, Figure 8 shows that the specific removal power for the studied parameters has a similar shape, and the diagrams can give valuable information to the plant operators.
Knowing the temperature and the inflow parameters (volume and pollutant concentration), the total daily load is calculated, and the operator can easily determine the volume of 40% FeCl3 solution to be used for the next 24 h. This is performed manually at this moment, taking into account the diagram in Figure 8 and the season. For instance, if the water temperature is 15 °C in autumn, the SRP is 2.8 L 40% ferric chloride for 1 kg of total nitrogen, but in spring, for the same temperature, the SRP is 4 L/kg total N (i.e., for the same nitrogen load a smaller volume of FeCl3 is required).
Although fast, this approach is not the best one, and in the future (2024) we intend to upgrade the WWTP with a system that will continuously measure the inflow load of ammonium and will automatically determine the FeCl3 volume, considering the proportionality between the ammonia and total nitrogen, as presented in Supplementary Material S1 (in our case, on average, the total nitrogen is 1.24 times more than ammonia nitrogen).

4. Conclusions

Although the existing regulations do not oblige WWTPs operating for communities with less than 10,000 PE to comply with discharge limits for nitrogen and phosphorus, environmental protection and common sense require their removal at affordable cost.
Our method, new in the literature, is the addition of 40% FeCl3 solution, without changing the design and operating parameters of our WWTP. The presence of ferric ions in water boosts the development of the microbiota responsible for both nitrification and denitrification, as well as phosphorus removal, discharging cleaner water.
For the quantification of the required FeCl3 volume, we introduced a new parameter, the specific removal power, which is easy to calculate and very helpful in determining the volume of ferric chloride at different seasonal temperatures.
This method is simple to use, and the good results at Agnita have encouraged us to extend it to other wastewater treatment plants operated by the Apa Tarnavei Mari Co.

Supplementary Materials

The following supporting information can be downloaded at: https://www.mdpi.com/article/10.3390/w14223670/s1, Supplementary Material S1 N P Operational Data 2021–2022; Supplementary Material S2 Main Operational Parameters 2015–2021.

Author Contributions

Conceptualization, E.G. and I.M.; data curation, E.G. and S.S.; methodology, E.G. and I.M.; software, I.M.; validation, I.M. and S.S.; formal analysis, E.G.; investigation, E.G.; writing—original draft preparation, E.G.; writing—review and editing, I.M.; supervision, S.S.; project administration, I.M. All authors have read and agreed to the published version of the manuscript.

Funding

This research received no external funding.

Data Availability Statement

Not applicable.

Acknowledgments

The authors kindly acknowledge the collaboration of the Agnita WWTP staff.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Bijekar, S.; Padariya, H.D.; Yadav, V.K.; Gacem, A.; Hasan, M.A.; Awwad, N.S.; Yadav, K.K.; Islam, S.; Park, S.; Jeon, B.-H. The State of the Art and Emerging Trends in the Wastewater Treatment in Developing Nations. Water 2022, 14, 2537. [Google Scholar] [CrossRef]
  2. Directive 91/271/EEC—Urban Wastewater Treatment. Available online: https://eur-lex.europa.eu/EN/legal-content/summary/urban-waste-water-treatment.html (accessed on 9 October 2022).
  3. Emergency Ordinance 195 22/12/2005. Available online: https://www.ecolex.org/details/legislation/emergency-ordinance-no-195-of-22-december-2005-on-environmental-protection-lex-faoc197188/?xdate_min=1997&xdate_max=2014&q=marine+plastic&type=legislation (accessed on 9 October 2022).
  4. NORMATIV NTPA-001/28.02.2002; Norms Concerning the Limits for Pollutants Load on Industrial and Municipal Wastewater Discharged in Natural Receiving Bodies (in Romanian), Monitorul Oficial of Romania, No. 187 of 20 March 2002. Available online: https://novainstal.ro/legislatie-mediu/normativ-ntpa-001-2002/ (accessed on 14 September 2022).
  5. NORMATIV NTPA-002/(28/02/2002—Norms Regarding Conditions for Wastewater Discharge in Municipal Sewerage Networks and Directly Towards Wastewater Treatment Plants (Actualized Version, in Romanian), Monitorul Oficial of Romania, No. 98 of 11 May 2005. Available online: https://legislatie.just.ro/Public/DetaliiDocumentAfis/98310 (accessed on 14 September 2022).
  6. Strungaru, S.A.; Nicoara, M.; Jitar, O.; Moglan, I.; Plavan, G. An overview on the development and progress of water supply and wastewater treatment in Romania. Environ. Eng. Manag. J. 2019, 18, 407–416. [Google Scholar] [CrossRef]
  7. Scalize, P.; Albuquerque, A.; Di Bernardo, L. Impact of alum water treatment residues on the methanogenic activity in the digestion of primary domestic wastewater sludge. Sustainability 2021, 13, 8783. [Google Scholar] [CrossRef]
  8. Von Sperling, M. Activated Sludge and Aerobic Biofilm Reactors; IWA Publishing: London, UK, 2015; Volume 6, ISBN 9781843391654. [Google Scholar]
  9. Garrone, P.; Grilli, L.; Groppi, A.; Marzano, R. Barriers and drivers in the adoption of advanced wastewater treatment technologies: A comparative analysis of Italian utilities. J. Clean. Prod. 2018, 171, S69–S78. [Google Scholar] [CrossRef] [Green Version]
  10. Márquez, P.; Gutiérrez, M.C.; Toledo, M.; Alhama, J.; Michán, C.; Martín, M.A. Activated sludge process versus rotating biological contactors in WWTPs: Evaluating the influence of operation and sludge bacterial content on their odor impact. Process Saf. Environ. Prot. 2022, 160, 775–785. [Google Scholar] [CrossRef]
  11. Banerjee, G. Hydraulics of bench-scale rotating biological contactor. Wat. Res. 1997, 31, 2500–2510. [Google Scholar] [CrossRef]
  12. Cortez, S.; Teixeira, P.; Oliveira, R.; Mota, M. Rotating biological contactors: A review on main factors affecting performance. Rev. Environ. Sci. Biotechnol. 2008, 7, 155–172. [Google Scholar] [CrossRef] [Green Version]
  13. Waqas, S.; Bilad, M.R. A review on rotating biological contactors. Indones. J. Sci. Technol. 2019, 4, 241–256. [Google Scholar] [CrossRef]
  14. Suzuki, T.; Yamaya, S. Removal of hydrocarbons in a rotating biological contactor with biodrum. Process Biochem. 2005, 40, 3429–3433. [Google Scholar] [CrossRef]
  15. Popa, M.; Ungureanu, N.; Vlăduț, V. Applications of Rotating Biological Contactorsin Wastewater Treatment. Cadastre Ser. 2019, 49, 136–145. [Google Scholar]
  16. Hassard, F.; Biddle, J.; Cartmell, E.; Jefferson, B.; Tyrrel, S.; Stephenson, T. Rotating biological contactors for wastewater treatment—A review. Process Saf. Environ. Prot. 2015, 94, 285–306. [Google Scholar] [CrossRef]
  17. Ni, B.J.; Pan, Y.; Guo, J.; Virdis, B.; Hu, S.; Chen, X.; Yuan, Z. CHAPTER 16: Denitrification Processes for Wastewater Treatment; The Royal Society of Chemistry: London, UK, 2017; ISBN 9781782623762. [Google Scholar]
  18. Heylen, K.; Vanparys, B.; Wittebolle, L.; Verstraete, W.; Boon, N.; De Vos, P. Cultivation of denitrifying bacteria: Optimization of isolation conditions and diversity study. Appl. Environ. Microbiol. 2006, 72, 2637–2643. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  19. Duque, A.F.; Bessa, V.S.; Castro, P.M.L. Bacterial community dynamics in a rotating biological contactor treating 2-fluorophenol-containing wastewater. J. Ind. Microbiol. Biotechnol. 2014, 41, 97–104. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  20. Mizyed, A.G. Review on Application of Rotating Biological Contactor in Removal of Various Pollutants from Effluent. Tech. Biochem. 2021, 2, 41–61. [Google Scholar]
  21. Rajta, A.; Bhatia, R.; Setia, H.; Pathania, P. Role of heterotrophic aerobic denitrifying bacteria in nitrate removal from wastewater. J. Appl. Microbiol. 2020, 128, 1261–1278. [Google Scholar] [CrossRef] [Green Version]
  22. Numberger, D.; Ganzert, L.; Zoccarato, L.; Mühldorfer, K.; Sauer, S.; Grossart, H.P.; Greenwood, A.D. Characterization of bacterial communities in wastewater with enhanced taxonomic resolution by full-length 16S rRNA sequencing. Sci. Rep. 2019, 9, 9673. [Google Scholar] [CrossRef] [Green Version]
  23. Gumaelius, L.; Magnusson, G.; Pettersson, B.; Dalhammar, G. Comamonas denitrificans sp. nov., an efficient denitrifying bacterium isolated from activated sludge. Int. J. Syst. Evol. Microbiol. 2001, 51, 999–1006. [Google Scholar] [CrossRef]
  24. Yan, Y.; Lu, H.; Zhang, J.; Zhu, S.; Wang, Y.; Lei, Y.; Zhang, R.; Song, L. Simultaneous heterotrophic nitrification and aerobic denitrification (SND) for nitrogen removal: A review and future perspectives. Environ. Adv. 2022, 9, 100254. [Google Scholar] [CrossRef]
  25. Wang, F.; Liu, W.; Liu, W.; Xiao, L.; Ai, S.; Sun, X.; Bian, D. Simultaneous removal of organic matter and nitrogen by heterotrophic nitrification–aerobic denitrification bacteria in an air-lift multi-stage circulating integrated bioreactor. Bioresour. Technol. 2022, 363, 127888. [Google Scholar] [CrossRef]
  26. Ziembińska-Buczyńska, A.; Ciesielski, S.; Żabczyński, S.; Cema, G. Bacterial community structure in rotating biological contactor treating coke wastewater in relation to medium composition. Environ. Sci. Pollut. Res. 2019, 26, 19171–19179. [Google Scholar] [CrossRef] [Green Version]
  27. Fang, H.; Olson, B.H.; Asvapathanagul, P.; Wang, T.; Tsai, R.; Rosso, D. Molecular biomarkers and influential factors of denitrification in a full-scale biological nitrogen removal plant. Microorganisms 2020, 8, 11. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  28. Holmes, D.E.; Dang, Y.; Smith, J.A. Nitrogen Cycling during Wastewater Treatment, 1st ed.; Elsevier Inc.: Amsterdam, The Netherlands, 2019; Volume 106, ISBN 9780128169759. [Google Scholar]
  29. Waqas, S.; Bilad, M.R.; Man, Z.; Wibisono, Y.; Jaafar, J.; Indra Mahlia, T.M.; Khan, A.L.; Aslam, M. Recent progress in integrated fixed-film activated sludge process for wastewater treatment: A review. J. Environ. Manag. 2020, 268, 110718. [Google Scholar] [CrossRef] [PubMed]
  30. Fazelipour, M.; Takdastan, A.; Borghei, S.M. Biological removal of nutrients (N & P) from urban wastewater with a modified integrated fixed-film activated sludge-oxic settling anoxic system using an anoxic sludge holding tank. Water Environ. J. 2021, 35, 830–846. [Google Scholar] [CrossRef]
  31. Kuśnierz, M.; Domańska, M.; Hamal, K.; Pera, A. Application of Integrated Fixed-Film Activated Sludge in a Conventional Wastewater Treatment Plant. Int. J. Environ. Res. Public Health 2022, 19, 5985. [Google Scholar] [CrossRef] [PubMed]
  32. Stuckey, D.C. Recent developments in anaerobic membrane reactors. Bioresour. Technol. 2012, 122, 137–148. [Google Scholar] [CrossRef]
  33. Tomczak, W.; Gryta, M. Energy-Efficient AnMBRs Technology for Treatment of Wastewaters: A Review. Energies 2022, 15, 4981. [Google Scholar] [CrossRef]
  34. Ouyang, C.F.; Chuang, S.H.; Su, J.L. Nitrogen and phosphorus removal in a combined activated sludge—RBC process. Proc. Natl. Sci. Counc. Repub. China Part A Phys. Sci. Eng. 1999, 23, 181–204. [Google Scholar]
  35. Teixeira, P.; Oliveira, R. Denitrification in a closed rotating biological contactor: Effect of disk submergence. Process Biochem. 2001, 37, 345–349. [Google Scholar] [CrossRef] [Green Version]
  36. Rodziewicz, J.; Mielcarek, A.; Janczukowicz, W.; Jóźwiak, T.; Struk-Sokołowska, J.; Bryszewski, K. The share of electrochemical reduction, hydrogenotrophic and heterotrophic denitrification in nitrogen removal in rotating electrobiological contactor (REBC) treating wastewater from soilless cultivation systems. Sci. Total Environ. 2019, 683, 21–28. [Google Scholar] [CrossRef]
  37. Trifi, I.M.; Trifi, B.; Djemal, A.; Hamrouni, B. Simultaneous removal of nitrates and nitrites from water by Donnan dialysis using Doehlert design. Environ. Eng. Manag. J. 2021, 20, 973–983. [Google Scholar] [CrossRef]
  38. Gupta, A.B.; Gupta, S.K. Simultaneous carbon and nitrogen removal from high strength domestic wastewater in an aerobic RBC biofilm. Water Res. 2001, 35, 1714–1722. [Google Scholar] [CrossRef]
  39. Breviar de Calcul Tehnologic—Statie de Epurare Agnita—Linia Apei; internal document; available on demand; pp. 1–21. (In Romanian)
  40. Mohamed, M.A.; Fouad, A.H.; ElHefny, R.M. Reviewing Rotating Biological Contactor’s Different Aspects for Wastewater Treatment with Experiment. Eng. Res. J. Fac. Eng. 2022, 51, 180–187. [Google Scholar] [CrossRef]
  41. Sathyapriya, K.; Chinnusamy, C. Reed Bed System: An Option for Reclamation of Polluted Water Resources: A Review. Agric. Rev. 2019, 40, 81–92. [Google Scholar] [CrossRef]
  42. Eikelboom, D.H. Process Control of Activated Sludge Plants by Microscopic Investigation; IWA Publishing: London, UK, 2000. [Google Scholar]
  43. Karczmarczyk, A.; Kowalik, W. Combination of Microscopic Tests of the Activated Sludge and Effluent Quality for More Efficient on-site Treatment. Water 2022, 14, 489. [Google Scholar] [CrossRef]
  44. NORMATIV NTPA-011/20.03.2002; Technical Norms for Collection, Treatment and Discharge of Municipal Wastewater, Monitorul Oficial of Romania, No. 187 of 20 March 2002. Available online: https://lege5.ro/gratuit/gqytamjy/norma-tehnica-privind-colectarea-epurarea-si-evacuarea-apelor-uzate-orasenesti-ntpa-011-din-28022002 (accessed on 14 September 2022). (In Romanian).
  45. Rebosura, M.; Salehin, S.; Pikaar, I.; Sun, X.; Keller, J.; Sharma, K.; Yuan, Z. A comprehensive laboratory assessment of the effects of sewer-dosed iron salts on wastewater treatment processes. Water Res. 2018, 146, 109–117. [Google Scholar] [CrossRef]
  46. Ghernaout, D. Water Treatment Coagulation: Dares and Trends. OALib 2020, 7, 1–18. [Google Scholar] [CrossRef]
  47. Gaspar, E.; Sava, C.; Caratus, M.; Barbu, C.H. Correlations among Parameters and Indicators within a Wastewater Treatment Plant. Case Study: The Wwtp of Medias, Romania. Environ. Eng. Manag. J. 2022, 21, 831–838. [Google Scholar]
  48. Gaşpar, E.; Barbu, C.H. The influence of ferric chloride on the active sludge within the municipal wastewater treatment plants. Int. Multidiscip. Sci. GeoConference Surv. Geol. Min. Ecol. Manag. SGEM 2018, 18, 733–738. [Google Scholar] [CrossRef]
  49. Earhart, C.F. Uptake and Metabolism of Iron and Molybdenum. In Escherichia Coli and Salmonella: Cellular and Molecular Biology, 2nd ed.; Neidhardt, F.C., Curtiss, R., III, Ingraham, J.L., Lin, E.C.C., Low, K.B., Magasanik, B., Reznikoff, W.S., Riley, M., Schaechter, M., Eds.; ASM Press: Washington, DC, USA, 1996; pp. 1075–1090. [Google Scholar]
  50. Kim, B.J.; Park, J.H.; Park, T.H.; Bronstein, P.A.; Schneider, D.J.; Cartinhour, S.W.; Shuler, M.L. Effect of iron concentration on the growth rate of Pseudomonas syringae and the expression of virulence factors in hrp-inducing minimal medium. Appl. Environ. Microbiol. 2009, 75, 2720–2726. [Google Scholar] [CrossRef] [Green Version]
  51. Waqas, S.; Bilad, M.R.; Man, Z.B. Performance and energy consumption evaluation of rotating biological contactor for domestic wastewater treatment. Indones. J. Sci. Technol. 2021, 6, 101–112. [Google Scholar] [CrossRef]
  52. Cvetkovic, D.; Susterstic, V.; Gordic, D.; Bojic, M.; Stosic, S. Perfomance of single-stage rotating biological contactor with supplemental aeration. Environ. Eng. Manag. J. 2014, 13, 681–688. [Google Scholar] [CrossRef]
Figure 1. Flowchart of the Agnita WWTP.
Figure 1. Flowchart of the Agnita WWTP.
Water 14 03670 g001
Figure 2. The RBCs of Agnita: the modules (left), and discs (right).
Figure 2. The RBCs of Agnita: the modules (left), and discs (right).
Water 14 03670 g002
Figure 3. Removal efficiency for the main pollutants during the period 2015–2021.
Figure 3. Removal efficiency for the main pollutants during the period 2015–2021.
Water 14 03670 g003
Figure 4. Microscopic image of aerobic microorganisms (magnification 100×).
Figure 4. Microscopic image of aerobic microorganisms (magnification 100×).
Water 14 03670 g004
Figure 5. Microscopic image of anaerobic microorganisms (magnification 100×).
Figure 5. Microscopic image of anaerobic microorganisms (magnification 100×).
Water 14 03670 g005
Figure 6. Seasonal variation in water temperature, SRP, and FeCl3 consumption for the last 12 months (September 2021–August 2022).
Figure 6. Seasonal variation in water temperature, SRP, and FeCl3 consumption for the last 12 months (September 2021–August 2022).
Water 14 03670 g006
Figure 7. SRPs for total nitrogen, ammonia nitrogen, and phosphorus.
Figure 7. SRPs for total nitrogen, ammonia nitrogen, and phosphorus.
Water 14 03670 g007
Figure 8. Correlations between water temperature and specific removal power for: Left: total nitrogen; Right: ammonia nitrogen.
Figure 8. Correlations between water temperature and specific removal power for: Left: total nitrogen; Right: ammonia nitrogen.
Water 14 03670 g008
Table 1. Means of the multi-annual inflow concentration and load values.
Table 1. Means of the multi-annual inflow concentration and load values.
Inflow ConcentrationInflow Load
BOD220mg/L573kg/day
COD440mg/L1147kg/day
TSS256mg/L667kg/day
TKN45mg/L118kg/day
Total P9mg/L24kg/day
Table 2. Biodisc characteristics.
Table 2. Biodisc characteristics.
CharacteristicValueCharacteristicValue
Type of RBCModularDisc diameter (mm)3000
Number of lines4Disc thickness (mm)1.5
Line volume (m3)58.87Distance between discs (mm)20
Number of modules per line2Disc materialHDPE
Number of biodisc sets per module2Rotation speed (min−1)2
Number of individual discs per set103 (each of 10 sectors)Water retention time (hours)2.17
Table 3. Parameters and their analytical methods used in the Agnita WWTP.
Table 3. Parameters and their analytical methods used in the Agnita WWTP.
ParameterAnalytical Standard or MethodEquipmentMaximal Permitted Limits mg/L
pHSR ISO 10523/2012, PO-01WTW pH/Conductivity Multimeter model 330i with SENTIX® 41 electrode6.5–8.5
CODSR ISO 6060/1996Velp eco 16 thermoreactor
Merck Spectroquant® Multy Spectrophotometer
125.0
BODSR EN ISO 5815-1/2020
Method WTW 997,230 OxiTop, PO-07
WTW incubator model TS 606/2-i
WTW OxiTop® bottles
25.0
NH4+SR ISO 7150-1/2001WTW PhotoLab S6 SpectrophotometerNot yet
Total NSR EN 25,663:2000
Method WTW Ntot TC LR 251995, PO-09
WTW Thermoreactor CR 2200,
Merck Spectroquant® Multy Spectrophotometer
15.0
Total PSR EN ISO 6878/2008WTW Thermoreactor CR 2200,
Merck Spectroquant® Multy Spectrophotometer
Not yet
TSSSR EN 872/2009Classical filtration equipment35.0
Table 4. Phosphorus removal after the use of FeCl3.
Table 4. Phosphorus removal after the use of FeCl3.
YearInflow
m3
Total P, mg/LElimination
Efficiency, %
InfluentEffluent
2016419,2715.833.5239.62
2017351,6625.763.3841.32
2018382,0114.482.0953.35
2019335,1855.542.751.26
2020253,7936.652.7259.10
2021307,9256.673.0353.46
Table 5. Removal efficiency of the major equipment.
Table 5. Removal efficiency of the major equipment.
Parameter
Sampling Place
20212022
NH4+
mg/L
Total N
mg/L
NH4+
mg/L
Total N
mg/L
Influent45.354740.5453.09
After primary settler33.23935.2246.08
Removal efficiency—primary settler26.7917.0213.1213.20
After biodiscs5.0113.503.8015.00
Removal efficiency biodiscs84.9165.3889.2167.45
After secondary settler4.1610.792.3811.75
Removal efficiency—secondary settler16.9720.0737.3721.67
Total removal efficiency90.8377.0494.1377.87
Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Share and Cite

MDPI and ACS Style

Gaspar, E.; Munteanu, I.; Sintea, S. Removal of N and P in a Rotating Biological Contactor Plant: Case Study Agnita, Romania. Water 2022, 14, 3670. https://doi.org/10.3390/w14223670

AMA Style

Gaspar E, Munteanu I, Sintea S. Removal of N and P in a Rotating Biological Contactor Plant: Case Study Agnita, Romania. Water. 2022; 14(22):3670. https://doi.org/10.3390/w14223670

Chicago/Turabian Style

Gaspar, Eniko, Ioan Munteanu, and Silviu Sintea. 2022. "Removal of N and P in a Rotating Biological Contactor Plant: Case Study Agnita, Romania" Water 14, no. 22: 3670. https://doi.org/10.3390/w14223670

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop