Next Article in Journal
Biophysical Benefits Simulation Modeling Framework for Investments in Nature-Based Solutions in São Paulo, Brazil Water Supply System
Next Article in Special Issue
Treatment of Saline Irrigation Water Using a Sulfate-Reducing Bioreactor Coupled with an Iron-Based Desalination Reactor
Previous Article in Journal
Integration of Distributed Streamflow Measurement Metadata for Improved Water Resource Decision-Making
Previous Article in Special Issue
Effect of Using Trichoderma spp. on Turfgrass Quality under Different Levels of Salinity
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Assessment of Surface Water Quality Using Water Quality Index and Discriminant Analysis Method

1
Laboratoire de Recherche Appliquée en Hydraulique, Université Mostafa Ben Boulaid Batna2, Batna 5000, Algeria
2
Laboratory of Biomaterials and Transport Phenomena, University of Medea, Medea 26000, Algeria
3
Ecole Nationale Supérieure de Chimie de Rennes, CNRS, ISCR–UMR6226, Université Rennes, F-35000 Rennes, France
4
Laboratoire de Gestion et de Valorisation des Ressoreces et Assurance Qualité, Faculté de la Nature et de vie et Sciences de la Terre, Université de Bouira, Bouira 10000, Algeria
*
Authors to whom correspondence should be addressed.
Water 2023, 15(4), 680; https://doi.org/10.3390/w15040680
Submission received: 18 January 2023 / Revised: 5 February 2023 / Accepted: 7 February 2023 / Published: 9 February 2023
(This article belongs to the Special Issue Desalination Treatment of Irrigation Water)

Abstract

:
Given the complexity of water quality data sets, water resources pose a significant problem for global public order in terms of water quality protection and management. In this study, surface water quality for drinking and irrigation purposes was evaluated by calculating the Water Quality Index (WQI) and Irrigation Water Quality Index (IWQI) based on nine hydrochemical parameters. The discriminant analysis (DA) method was used to identify the variables that are most responsible for spatial differentiation. The results indicate that the surface water quality for drinking is of poor and very poor quality according to the WQI values, however, the IWQI values indicate that the water is acceptable for irrigation with restrictions for salinity sensitive plants. The discriminate analysis method identified pH, potassium, chloride, sulfate, and bicarbonate as the significant parameters that discriminate between the different stations and contribute to spatial variation of the surface water quality. The findings of this study provide valuable information for decision-makers to address the important problem of water quality management and protection.

1. Introduction

Water is essential for the survival of all living organisms and plays a vital role in the growth and development of life on Earth [1,2,3,4,5,6]. Therefore, it is imperative to take immediate action to preserve water resources through effective management and monitoring of water quality [7,8,9,10,11]. The usage of water for domestic purposes accounts for only 5%, with 20% being utilized by the industrial sector, leaving 75% for agricultural use [12,13]. It is crucial to implement a comprehensive program for water resource development that places emphasis on water quality management and monitoring.
It is crucial to evaluate the quality of water before it is used for human consumption [14,15,16]. The pollution of surface waters is a direct result of industrial development, as well as the excessive and uncontrolled use of fertilizers by man, in addition to natural processes such as the dissolution of rocks through water-rock interaction [17]. The assessment of water quality can be conducted through the use of the water quality index (WQI) model, which primarily depends on the physicochemical parameters of water, to monitor and control the quality of water intended for human consumption [18,19,20,21,22].
The study of the spatio-temporal variation of surface waters is a complex phenomenon, but the use of outdated methods can lead to suboptimal performance of the model and redundant results. In this study, factor analysis (FA), discriminant analysis (DA), cluster analysis (CA), and principal component analysis (PCA) methods were used to evaluate the quality of surface waters and reduce the number of monitoring results and the identification of measurement stations of comparable quality, as well as to separate measurement stations where the water quality deviates from the quality of other measurement stations [23,24]. The objectives of this study are to understand the current state of water quality, determine the suitability of surface waters for human consumption, provide scientific recommendations for water resource managers and, finally, identify the most influential parameters and those responsible for the spatial differentiation of water quality using the discriminant analysis (DA) method.

2. Materials and Methods

2.1. Study Area

The Koudiat Medouar watershed is located in northeastern Algeria, in the Aurès region, and is a part of the vast watershed of the Constantine Highlands, which has a total area of 9500 km2. It is between four huge basins to the north of Kebir Rhumel and Seybouse, to the east of Medjerda, to the south of Chot Hodna and Melghir, and to the west of Summam. It has a 590 km2 land area. It is situated between the longitude of 35°30′57″ North and the latitude of 6°30′48″ East (Figure 1). In northeastern Algeria, the Koudiat Medouar watershed contributes significantly to the surface water mobilization and transfer system in the high plains of Constantine and the Aurès. The Oued Chemorah basin provides water for the dam, as well as sub-basins, wastewater, and industrial water from neighboring municipalities. Due to recent droughts in the region, authorities have also utilized water from the Beni Haroun dam, which has a capacity of 74 million cubic meters. This region’s climate is semi-arid, with a cold and humid winter and a hot and dry summer, given the semi-arid character of the study region which results in a more or less marked drought by a very high potential evaporation rate which is estimated at 1747.34 mm per year. The average annual rainfall and temperature are around 370 mm and 15 °C, respectively [25].

2.2. Sampling of Surface Water

The following sample stations were selected depending on the degree of pollution in the research area: Dam station, Oued Reboua station, Oued Timgad station, and Wastewater station. The surface water samples were collected over a two-year period (2019 to 2020), with two samples taken at the beginning and end of each month in accordance with conventional sampling protocols [26] guidelines on consumption and irrigation from the International Organization for Standardization (ISO) [27], the Bureau of International Standards (BIS) [28], and the Food and agriculture organization (FAO) [29]. The samples from the sampling stations were placed in polyethylene bottles, which were then transported in coolers to the analysis laboratory. Nitric acid (HNO3) was added to the cationic solutions to achieve a pH of 2, but the ion balance is computed with errors of less than 10%. Table 1 summarizes the findings.

2.3. Water Quality Index (WQI)

In this study, two equations were used to evaluate the quality of surface water intended for consumption and irrigation. The first is the water quality index (WQI), which is classified into five different suitability classes (Table 2). The second is the Irrigation Water Quality Index (IWQI), which is classified into four different suitability classes (Table 3). Both equations abide to the parameters proposed by the World Health Organization (WHO).
In the present research, the WQI was calculated using seven hydrochemical parameters: Ca, Mg, Na, K, Cl, SO4, and HCO3. There were three processes involved in calculating WQI.
First, each hydrochemical measure was allocated a weight based on its relative relevance to the overall quality of drinking and irrigation water.
The parameters (Ca and HCO3) have significant influence on the quality of surface waters, and hence the greatest weight of 5 was allocated to them. In contrast, the parameter (K), which is believed to be non-harmful, was assigned the lowest weight of 2. (Table 4).
Step two involves calculating the relative weight (Wi) of each hydrochemical parameter using Equation (1).
W i = w i i = 1 n w i
where Wi is the relative weight, wi is the weight of each parameter, and n is the number of parameters.
Step three: for each hadrochemical parameter, the quality scale (qi) is computed by dividing its concentration in each water sample by its respective standard [29,30], and then multiplying the result by 100 in accordance with Equation (2).
q i = C i S i * 100
where qi is the quality grading, Ci is the concentration of each hydrochemical parameter in each water sample, and Si is the concentration of standard hydrochemical concentration either for drinking water or for irrigation purposes proposed by different organizations [29,30].
Finally, Water Quality Index (WQI) is calculated by the following Equation:
W Q I = i = 1 n w i * q i
where WQI and IWQI are the quality indexes used to evaluate the quality of drinking water and irrigation water, respectively. Wi denotes the relative weight of each hydrochemical parameter, and qi refers to the quality rating.

2.4. National Sanitation Foundation Water Quality Index

Seven parameters calcium (Ca2+), magnesium (Mg2+), potassium (K+), sodium (Na+), chloride (Cl), sulfate (SO42−), and bicarbonate (CaCO3) were used to calculate the NSFQWI. The graphical representation shows that the water quality level varies from 0 (very poor) to 100 (excellent), the value of Q is determined by comparing the values of these parameters to this weighting curve, and the value of Q is multiplied by a weighting factor which is based on the degree its importance in the calculation (Wi) [31].
NSFWQI classes are represented in intervals that express water quality: very poor (0–25), poor (25–50), average (50–70), good (70–90), and excellent (90–100).

2.5. Discriminant Analysis (DA)

The technique of discriminant analysis is used to demonstrate the connection and linear combinations between two or more independent metric variables. Calculating the discriminant function is as follows:
f ( G i ) = K i + j = 1 n W i j · P i j
where i represents the number of groups or stations (G). In the current study, four stations (groups) were selected: Ki represents the constant inherent to each group; n, is the number of variables used to categorize a set of data into a given class, Wj, is the weight coefficient, assigned by DA to a specified selected parameter Pj; and Pj, is the analytical value of the selected variable. In this study, the independent variables were the hydrochemical parameters in the four stations.
All statistical and multivariate data analysis methods, as well as visualization, were performed using R version 4.1.3 and SPSS version 28.0.1.

3. Results and Discussion

3.1. Descriptive Statistics

The descriptive statistics of surface water hydrochemical parameters may offer an approximation of the hydrochemical characteristics of a region. Table 5 and Figure 2 provide statistics for each station’s surface water hydrochemical parameters. The pH range of the surface water samples was 6.8 to 8.6, suggesting that the surface water in the research region was mainly neutral or slightly alkaline [32,33]. Electrical conductivity (EC) values for Dam, Oued Reboua, Oued Timgad, and Wastewater station were 1349, 1010, 1326, and 1173 µS/cm, respectively. The coefficient of variation (in percent) of electrical conductivity was 22.42, 25.55, 8.81, and 15.82 for Dam, Oued Reboua, and Wastewater stations, respectively, indicating that the temporal variability of electrical conductivity was moderate at Dam, Oued Reboua, and Wastewater stations and low at Oued Timgad station. Ca > Na > Mg > K were the four locations with the highest average cation concentrations, as seen in Figure 2. In all stations, calcium was the predominant cation, followed by sodium. Dam, Oued Reboua, Oued Timgad, and Wastewater station had Ca concentrations of 94.04, 120.24, 116.93, and 107.84 mg/L, respectively. The Ca content in all surface water tests exceeded the WHO (2006) permissible limit [34]. HCO3 > SO4 > Cl was the predominant anion in the Oued Reboua, Oued Timgad, and Wastewater sites. In the case of the Dam station, HCO3 > Cl > SO4 was the dominant anion. Bicarbonate was the most prevalent anion in all four sites, followed by sulfate at Oued Reboua, Oued Timgad, and Wastewater and chloride at the Dam station. The main concentration of HCO3 was 173.21, 307.28, 500.51, and 758.38 mg/L in the four stations, respectively. The highest value of HCO3 was observed in the Wastewater and Oued Timgad stations.

3.2. Evaluation of Surface Water Quality

This research used the water quality index for drinking (WQI) and irrigation (IWQI) water purposes for assessing surface water quality in terms of analyzed parameters. Table 5 displays the summary statistics for each station’s water quality index. Boxplots of WQI and IWQI for each station are shown in Figure 3.
The calculated WQI values were divided into five categories: excellent, good, poor, very poor, and unsuitable for human consumption. Dam, Oued Reboua, Oued Timgad, and Wastewater station had WQI values of 58.15, 68.05, 75.30, and 82.07, respectively. The Wastewater station’s water samples had the highest WQI values. Estimated WQI values varied from 50.88 to 95.26, indicating that none of the surface water samples contain ‘Excellent’ or ‘Good’ drinking water (WQI 50). As demonstrated in Figure 3, all surface water samples collected at the Dam station were of poor quality. A total of 75% of the water samples collected at the Oued Reboua station were judged to be of poor quality. However, almost all water samples from the Oued Timgad and Wastewater sites were determined to be of very poor quality.
The Water Quality Indices for irrigation (IWQI) reveal the level of pollution based on the restriction standards established for each class. According to Table 4, zone one (I) is the unrestricted class, zone two (II) expresses the class requiring restriction, zone three (III) indicates the moderate restriction class, and zone four (IV) expresses the severe restriction class [35].
Figure 3 displays that the highest surface water quality index values for irrigation in the research region were 27.80, 36.22, 41.26, and 54.44, respectively. However, these values indicate that they are classed in zone one, which indicates class (I) of no restrictions on soils and crops.
The NSFWQI values presented in Table 6 show that all the samples were classified as medium (NSFWQI = 50–70), except for the samples from the dam station which were classified as good (NSFWQI = 72.82); this increase is due to the decrease in potassium (K+) and chloride (Cl) concentrations [31].

3.3. Correlation Analysis

In addition to identifying the origins of the hydrochemical formation process and establishing the degree of relevance between elements [36], the correlation research was used to demonstrate the numerous types of correlations between the physico-chemical parameters evaluated in the study region.
Using the corrplot package in R [37], the correlation matrix between the hydrochemical parameters, WQI, and IWQI for each station is presented in Figure 4 in this section. The correlation matrix was created using Pearson’s correlation analysis.

3.3.1. Dam Station

Figure 4 demonstrates that EC had a negative correlation with Mg, HCO3, SO4, and IWQI, indicating that ions are prevalent in the research region. HCO3, Cl, and IWQI all correlate positively with WQI. IWQI demonstrated a statistically significant positive correlation with Mg, HCO3, Cl, and SO4. In addition, a substantial positive correlation was identified between Mg-HCO3 and SO4-K.

3.3.2. Oued Reboua Station

Ca had a substantial positive correlation with SO4 according to the data, suggesting that both parameters may have the same source. In addition, a substantial association was found between IWQI and K. (0.99).

3.3.3. Oued Timgad Station

Figure 4 shows that IWQI, Cl, SO4, Mg, Na, and K exhibited a substantial positive correlation with WQI, suggesting that these hydrochemical parameters have a considerable impact on water quality. IWQI was positively correlated with Cl, SO4, Mg, and NA. There was a substantial correlation between potassium (K) and pH, Cl, SO4, and Na.

3.3.4. Wastewater Station

Figure 4 reveals that the bicarbonate parameter had a strong correlation with WQI and IWQI, showing that HCO3 plays a significant role in influencing the surface water quality in the research region. The sodium (Na) parameter correlated positively with EC, Cl, Mg, and K, but negatively with pH and Ca. In addition, a high positive correlation between Ca and Mg suggests that these parameters may have the same source.
Significant correlations were explained by the dissolution of the rock’s mineral composition and the exchange of ions, which generates precipitation, human activity, and the addition of chemical fertilizers that pollute surface waters via runoff and leaching from agricultural land [32,33].

3.4. Spatial Variation in Surface Water Quality

The spatial variation in surface water quality was analyzed using discriminant analysis (DA) conducted on the raw dataset consisting of 10 variables grouped into four stations (pH, EC, Ca, Mg, Na, K, Cl, SO4, HCO3, WQI, and IWQI). The stepwise mode of DA was employed, in which at each step, one variable that minimized the overall Wilks’ Lambda statistic was added or removed. The aim was to identify the most crucial variables that contributed to the differences among the various stations. The independent variables were the main hydrochemical parameters that were measured, and the dependent variable consisted of four stations.
Since the p-values are less than the 0.01 level of significance, the Wilks’ Lambda statistic for group mean equality is significant. Test F for Wilks’ Lambda was used to identify the factors that substantially contributed to station differentiation. Table 7 displays the ANOVA findings. From the results, we can see that the Test F is significant for eight variables (pH, Ca, Mg, Cl, SO4, HCO3, WQI, and IWQI) out of eleven variables at p-level < 0.05. The three variables of electrical conductivity (EC), sodium (Na), and potassium (K), for which the significance (Sig.) is higher than 0.01, should be eliminated from the model.
Table 8 provides an overview of canonical discriminant functions. Four stations were analyzed using three discriminant functions (DFs), and therefore, three eigenvalues in a discriminant analysis.
The first discriminant function has the greatest eigenvalue, suggesting that it has the strongest discrimination power of the three. From Table 8, we can see that the first function explained 77.2% of the total variance between stations, compared to the other two functions that unite the studied parameters, indicating a dispersion of less than 20%. However, the canonical correlation coefficient, which measures the ratio between the coordinates of the discriminating factor and the grouping variable, explained only 94.3%, or (0.971)2, of the total variance, indicating a difference.
Table 9 displays the Wilks’ Lambda and Chi-square statistics for each discriminant function (DF). According to Table 8, the Wilks’ Lambda and Chi-square statistics for each discriminant function (DF) were between 0.007 and 0.64 and 13.859 and 156.66, respectively. Wilk’s Lambda statistic indicated that all three functions were statistically significant since their values are were less than 0.01, showing that the spatial discriminant analysis was effective and significant.
Considered discriminating variables are expressed in various units of measurement [38]. The coefficients of the discriminant function are used to determine the discriminant score for each case. Given that the first function has the largest discriminating power, it is clear to focus on analyzing its output. The findings of the first discriminant function demonstrate that bicarbonate (HCO3) was an important hydrochemical parameter for discriminating the spatial variation in surface water quality across four stations. Table 10 presents the normalized coefficients of the discriminant function.
The structure matrix coefficient represents the relationship between every predictor variable and the discriminant function. Although the correlation coefficient of bicarbonate, which admits a high value, is strongly correlated with the first discriminant function, the chloride and pH are strongly correlated with the second discriminant function, whereas the coefficients of sulfate and potassium are well correlated with the third discriminant function. The values of the calculated structural coefficients are shown in Table 11.
The first discriminant function clearly illustrates the spatial variation between the four sites, as seen in Table 12.
Table 13 and Table 14 show the resulting classification matrices (CMs) and classification functions (CFs) from the discriminant analysis. From the findings, we can observe that the DA properly categorized 97.3% of the cases that were originally grouped. According to Table 13 and Table 14, the DA effectively categorized 94.6% of the initially grouped cases in the classification matrix. Based on the findings of discriminant analysis, the most significant discriminant variables across the four geographical stations (Table 13) were pH, potassium, chloride, sulfate, and bicarbonate, causing the majority of expected surface water quality variations.

4. Conclusions

In the context of this work, physico-chemical parameters (pH, EC, Ca, Mg, Na, K, Cl, SO4, and HCO3) were used to calculate the surface water quality indexes for potability (WQI) and irrigation (IWQI). All samples were collected monthly at four sites throughout 2019 and 2020.
Discriminant analysis (DA) is a crucial technique for producing a thorough interpretation of the acquired data, allowing managers to use them for improved surface water pollution management of water resources.
Based on the WQI, the results show that the water samples from the four stations are of poor and very poor quality for potability. According to the IWQI, the water quality of the research area is adequate for irrigation, with restrictions for salinity-sensitive plants, while the NSFWQI reflects the same water quality as the IWQI or samples are classified as fair water, except for samples from dam stations which classified as good quality water.
Using discriminant analysis, the spatial variation in surface water quality across the four sites was examined (DA). The discriminant analysis revealed the presence of pH, potassium, chloride, sulfate, and bicarbonate. These discriminating parameters are the most relevant at the four sites and contribute in the majority of cases to the predicted changes in surface water quality.

Author Contributions

Conceptualization, A.M., L.B., A.T. and H.S.; methodology, A.M. and D.B.; software, A.M. and H.T.; validation, E.L., A.A. and L.M.; investigation, A.M., writing—original draft preparation, A.M., A.T. and L.B.; writing—review and editing, D.B., E.L., H.T. and H.S.; visualization, L.M. and A.A.; supervision, A.A. and L.M.; project administration, A.A. and L.M.; funding acquisition, L.M. and A.A. All authors have read and agreed to the published version of the manuscript.

Funding

This research received no external funding.

Institutional Review Board Statement

Not applicable.

Informed Consent Statement

Not applicable.

Data Availability Statement

Not applicable.

Acknowledgments

The authors wish to thank all who assisted in conducting this work.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Abdelwahab, O.; Amin, N.K. Adsorption of Phenol from Aqueous Solutions by Luffa Cylindrica Fibers: Kinetics, Isotherm and Thermodynamic Studies. Egypt. J. Aquat. Res. 2014, 39, 215–223. [Google Scholar] [CrossRef]
  2. Tahraoui, H.; Belhadj, A.-E.; Hamitouche, A.; Bouhedda, M.; Amrane, A. Predicting the Concentration of Sulfate (SO42−) in Drinking Water Using Artificial Neural Networks: A Case Study: Médéa-Algeria. Desalination Water Treat. 2021, 217, 181–194. [Google Scholar] [CrossRef]
  3. Tahraoui, H.; Belhadj, A.-E.; Hamitouche, A.-E. Prediction of the Bicarbonate Amount in Drinking Water in the Region of Médéa Using Artificial Neural Network Modelling. Kem. U Ind. Časopis Kemičara I Kem. Inženjera Hrvat. 2020, 69, 595–602. [Google Scholar] [CrossRef]
  4. Hadadi, A.; Imessaoudene, A.; Bollinger, J.-C.; Bouzaza, A.; Amrane, A.; Tahraoui, H.; Mouni, L. Aleppo Pine Seeds (Pinus Halepensis Mill.) as a Promising Novel Green Coagulant for the Removal of Congo Red Dye: Optimization via Machine Learning Algorithm. J. Environ. Manag. 2023, 331, 117286. [Google Scholar] [CrossRef]
  5. Hadadi, A.; Imessaoudene, A.; Bollinger, J.-C.; Assadi, A.A.; Amrane, A.; Mouni, L. Comparison of Four Plant-Based Bio-Coagulants Performances against Alum and Ferric Chloride in the Turbidity Improvement of Bentonite Synthetic Water. Water 2022, 14, 3324. [Google Scholar] [CrossRef]
  6. Hadadi, A.; Imessaoudene, A.; Bollinger, J.-C.; Cheikh, S.; Assadi, A.A.; Amrane, A.; Kebir, M.; Mouni, L. Parametrical Study for the Effective Removal of Mordant Black 11 from Synthetic Solutions: Moringa Oleifera Seeds’ Extracts Versus Alum. Water 2022, 14, 4109. [Google Scholar] [CrossRef]
  7. Tahraoui, H.; Belhadj, A.-E.; Amrane, A.; Houssein, E.H. Predicting the Concentration of Sulfate Using Machine Learning Methods. Earth Sci. Inform. 2022, 15, 1–22. [Google Scholar] [CrossRef]
  8. Tahraoui, H.; Amrane, A.; Belhadj, A.-E.; Zhang, J. Modeling the Organic Matter of Water Using the Decision Tree Coupled with Bootstrap Aggregated and Least-Squares Boosting. Environ. Technol. Innov. 2022, 27, 102419. [Google Scholar] [CrossRef]
  9. Farch, S.; Yahoum, M.M.; Toumi, S.; Tahraoui, H.; Lefnaoui, S.; Kebir, M.; Zamouche, M.; Amrane, A.; Zhang, J.; Hadadi, A. Application of Walnut Shell Biowaste as an Inexpensive Adsorbent for Methylene Blue Dye: Isotherms, Kinetics, Thermodynamics, and Modeling. Separations 2023, 10, 60. [Google Scholar] [CrossRef]
  10. Imessaoudene, A.; Cheikh, S.; Hadadi, A.; Hamri, N.; Bollinger, J.-C.; Amrane, A.; Tahraoui, H.; Manseri, A.; Mouni, L. Adsorption Performance of Zeolite for the Removal of Congo Red Dye: Factorial Design Experiments, Kinetic, and Equilibrium Studies. Separations 2023, 10, 57. [Google Scholar]
  11. Imessaoudene, A.; Cheikh, S.; Bollinger, J.-C.; Belkhiri, L.; Tiri, A.; Bouzaza, A.; El Jery, A.; Assadi, A.; Amrane, A.; Mouni, L. Zeolite Waste Characterization and Use as Low-Cost, Ecofriendly, and Sustainable Material for Malachite Green and Methylene Blue Dyes Removal: Box–Behnken Design, Kinetics, and Thermodynamics. Appl. Sci. 2022, 12, 7587. [Google Scholar] [CrossRef]
  12. Pesce, S.F.; Wunderlin, D.A. Use of Water Quality Indices to Verify the Impact of Córdoba City (Argentina) on Suquía River. Water Res. 2000, 34, 2915–2926. [Google Scholar] [CrossRef]
  13. Rao, N.; Vidyasagar, G.; Rao, P.; Bhanumurthy, P. Assessment of Hydrogeochemical Processes in a Coastal Region: Application of Multivariate Statistical Model. J. Geol. Soc. India 2014, 84, 494–500. [Google Scholar] [CrossRef]
  14. Tahraoui, H.; Belhadj, A.-E.; Triki, Z.; Boudella, N.; Seder, S.; Amrane, A.; Zhang, J.; Moula, N.; Tifoura, A.; Ferhat, R.; et al. Mixed Coagulant-Flocculant Optimization for Pharmaceutical Effluent Pretreatment Using Response Surface Methodology and Gaussian Process Regression. Process Saf. Environ. Prot. 2022, 169, 909–927. [Google Scholar] [CrossRef]
  15. Bouchelkia, N.; Tahraoui, H.; Amrane, A.; Belkacemi, H.; Bollinger, J.-C.; Bouzaza, A.; Zoukel, A.; Zhang, J.; Mouni, L. Jujube Stones Based Highly Efficient Activated Carbon for Methylene Blue Adsorption: Kinetics and Isotherms Modeling, Thermodynamics and Mechanism Study, Optimization via Response Surface Methodology and Machine Learning Approaches. Process Saf. Environ. Prot. 2022, 170, 513–535. [Google Scholar] [CrossRef]
  16. Tahraoui, H.; Belhadj, A.-E.; Moula, N.; Bouranene, S.; Amrane, A. Optimisation and Prediction of the Coagulant Dose for the Elimination of Organic Micropollutants Based on Turbidity. Kem. U Ind. 2021, 70, 675–691. [Google Scholar] [CrossRef]
  17. Smith, V.H. Effects of Eutrophication on Maximum Algal Biomass in Lake and River Ecosystems. Inland Waters 2016, 6, 147–154. [Google Scholar] [CrossRef]
  18. Narsimha, A.; Taloor, A. Hydrogeochemical Investigation of Groundwater Quality in the Hard Rock Terrain of South India Using Geographic Information System (GIS) and Groundwater Quality Index (GWQI) Techniques. Groundw. Sustain. Dev. 2019, 10, 100288. [Google Scholar] [CrossRef]
  19. Tiri, A.; Belkhiri, L.; Asma, M.; Mouni, L. Suitability and Assessment of Surface Water for Irrigation Purpose. In Water Chemistry; Intechopen: London, UK, 2020; ISBN 978-1-78985-557-9. Available online: https://www.intechopen.com/profiles/289828 (accessed on 17 January 2023).
  20. Alver, A. Evaluation of Conventional Drinking Water Treatment Plant Efficiency According to Water Quality Index and Health Risk Assessment. Environ. Sci. Pollut. Res. 2019, 26, 27225–27238. [Google Scholar] [CrossRef]
  21. Wu, K.; Tizzani, R.; Zweers, H.; Rijnaarts, H.; Langenhoff, A.; Fernandes, T. Removal Processes of Individual and a Mixture of Organic Micropollutants in the Presence of Scenedesmus Obliquus. Sci. Total Environ. 2022, 838, 156526. [Google Scholar] [CrossRef]
  22. Maghrebi, M.; Noori, R.; Bhattarai, R.; Mundher Yaseen, Z.; Tang, Q.; Al-Ansari, N.; Madani, K. Iran’s agriculture in the Anthropocene. Earth’s Future 2020, 8, e2020EF001547. [Google Scholar] [CrossRef]
  23. Noori, R.; Sabahi, M.S.; Karbassi, A.R.; Baghvand, A.; Zadeh, H.T. Multivariate statistical analysis of surface water quality based on correlations and variations in the data set. Desalination 2010, 260, 129–136. [Google Scholar] [CrossRef]
  24. Noori, R.; Karbassi, A.; Khakpour, A.; Shahbazbegian, M.; Badam, H.M.K.; Vesali-Naseh, M. Chemometric analysis of surface water quality data: Case study of the Gorganrud River Basin, Iran. Environ. Model. Assess. 2012, 17, 411–420. [Google Scholar] [CrossRef]
  25. Tiri, A.; Belkhiri, L.; Mouni, L. Evaluation of Surface Water Quality for Drinking Purposes Using Fuzzy Inference System. Groundw. Sustain. Dev. 2018, 6, 235–244. [Google Scholar] [CrossRef]
  26. Federation, W.E.; Aph Association. Standard methods for the examination of water and wastewater. Am. Public Health Assoc. 2005, 1, 541. [Google Scholar]
  27. International Organization for Standardization (ISO). 1993. Available online: https://www.iso.org/obp/ui/#iso:std:iso-iec:2382:-1:ed-3:v1:en (accessed on 17 January 2023).
  28. Water–Specification, I.S.D. Bureau of Indian Standards. New Delhi India. 2012. pp. 1–12. Available online: http://cgwb.gov.in/documents/wq-standards.pdf (accessed on 17 January 2023).
  29. Steduto, P.; Faurès, J.-M.; Hoogeveen, J.; Winpenny, J.; Burke, J. Coping with Water Scarcity: An Action Framework for Agriculture and Food Security. FAO Water Rep. 2012, 16, 78. [Google Scholar]
  30. World Health Organization. Progress on Drinking Water, Sanitation and Hygiene: 2017 Update and SDG Baselines; World Health Organization: Geneva, Switzerland, 2017. [Google Scholar]
  31. Noori, R.; Berndtsson, R.; Hosseinzadeh, M.; Adamowski, J.F.; Abyaneh, M.R. A critical review on the application of the National Sanitation Foundation Water Quality Index. Environ. Pollut. 2019, 244, 575–587. [Google Scholar] [CrossRef]
  32. Belkhiri, L.; Mouni, L.; Sheikhy Narany, T.; Tiri, A. Evaluation of Potential Health Risk of Heavy Metals in Groundwater Using the Integration of Indicator Kriging and Multivariate Statistical Methods. Groundw. Sustain. Dev. 2017, 4, 12–22. [Google Scholar] [CrossRef]
  33. Tiri, A.; Lahbari, N.; Abderrahmane, B. Assessment of the Quality of Water by Hierarchical Cluster and Variance Analyses of the Koudiat Medouar Watershed, East Algeria. Appl. Water Sci. 2015, 7, 4197–4206. [Google Scholar] [CrossRef]
  34. World Health Organization; WHO. Guidelines for Drinking-Water Quality; World Health Organization: Geneva, Switzerland, 2004; Volume 1, ISBN 92-4-154638-7. [Google Scholar]
  35. Raychaudhuri, S.; Jena; Kumar, M.; Ashwani; Srivastava, S. WQI to Monitor Water Quality for Irrigation and Potable Use; Indian Council of Agricultural Research Bhubaneswar: Bhubaneswar, Indian, 2014. [Google Scholar]
  36. Jehan, S.; Muhammad, S.; Khan, S.; Khattak, S.; Muhammad, N.; Rashid, A. Hydrochemical Properties of Drinking Water and Their Sources Apportionment of Pollution in Bajaur Agency, Pakistan. Measurement 2019, 139, 249–257. [Google Scholar] [CrossRef]
  37. Wei, Y.; Yu, J.; Du, Y.; Li, H.; Su, C.-H. Artificial Intelligence Simulation of Pb(II) and Cd(II) Adsorption Using a Novel Metal Organic Framework-Based Nanocomposite Adsorbent. J. Mol. Liq. 2021, 343, 117681. [Google Scholar] [CrossRef]
  38. Jaba, E.; Jemna, D.; Viorica, E.-D.; Balan, C. Discriminant Analysis in the Study of Romanian Regional Economic Development. An. Ştiinţifice Ale Univ. “Alexandru Ioan Cuza” Din Iaşi Tomul LIV Ştiinţe Econ. 2007, 54, 147–153. [Google Scholar]
Figure 1. Location of the study area and sampling points.
Figure 1. Location of the study area and sampling points.
Water 15 00680 g001
Figure 2. Boxplot of the hydrochemical parameters of the surface water.
Figure 2. Boxplot of the hydrochemical parameters of the surface water.
Water 15 00680 g002
Figure 3. Boxplot of water quality index: WQI for drinking purposes (left) and IWQI for irrigation purposes (right).
Figure 3. Boxplot of water quality index: WQI for drinking purposes (left) and IWQI for irrigation purposes (right).
Water 15 00680 g003
Figure 4. Correlation analysis of hydrochemical parameters for each station (p-value < 0.01).
Figure 4. Correlation analysis of hydrochemical parameters for each station (p-value < 0.01).
Water 15 00680 g004
Table 1. Instrumental and titrimetric techniques used for the chemical analysis of samples of surface water.
Table 1. Instrumental and titrimetric techniques used for the chemical analysis of samples of surface water.
ParametersCharacteristicsAnalytical MethodRangeUnit
GeneralpHpH/EC/TDS meterpH 4.7 and 9.2
Electrical conductivitypH/EC/TDS meterPotassium chlorideµS/cm
Total dissolved solids (TDS)CalculationEC X (0.55–0.75)mg/L
Total hardness (CaCO3)EDTA titrimetricEDTA, ammonia buffermg/L
and Eriochrome
Black-T (EBT) indicator
Major cationsCalcium (Ca)EDTA titrimetricEDTA, sodium hydroxidemg/L
and murexide
Magnesium (Mg)CalculationMgH = TH − CaH;Mg = MgH × Eqmg/L
Wt of Mg × Normality of EDTA
Sodium (Na)Flame photometricSodium chloride (NaCl) and KClmg/L
Potassium (K)Flame photometricNaCl and KClmg/L
Major anionsBicarbonates (HCO3)TitrimetricHydrosulfuric acide (H2SO4)mg/L
phenlphthalein and methyl orange
Chloride (Cl)TitrimetricSilver nitrate (AgNO3)mg/L
potassium chromate
Sulfates (SO4)UV-visible spectrophotometerHCI, ethyl alcohl, NaClmg/L
barium chloride, sodium sulfate
Nitrate (NO3)UV-visible spectrophotometerPotassium nitrate (KNO3)mg/L
Phenol disulfonic acide, ammonia
Table 2. Classification of Water Quality Index (WQI) of drinking water.
Table 2. Classification of Water Quality Index (WQI) of drinking water.
WQI ValuesWater Quality for Drinking Purpose
Less than 25Excellent
26–50Good
51–75Poor
76–100Very poor
More than 100Unsuitable
Table 3. Categorization of Water Quality Index (IWQI) of irrigation water.
Table 3. Categorization of Water Quality Index (IWQI) of irrigation water.
IWQI ValuesClassRestriction
Less than 150INone
150–300IISlight
301–450IIIModerate
More than 450IVSevere
Table 4. Weight and relative weight of the hydrochemical parameters.
Table 4. Weight and relative weight of the hydrochemical parameters.
ParametersCaMgNaKClSO4HCO3
WHO (2017)755020010250250500
FAO (1985)40060920210651920610
Weight (wi)
Dam5342435
Oued Rboua5342345
Oued Timgad5342345
Wastewater5342345
Relative weight (Wi)
Dam0.19230.11540.15380.07690.15380.11540.1923
Oued Rboua0.19230.11540.15380.07690.11540.15380.1923
Oued Timgad0.19230.11540.15380.07690.11540.15380.1923
Wastewater0.19230.11540.15380.07690.11540.15380.1923
Note(s): WHO: World Health Organization (2017); FAO: Food and Agriculture Organization (1985).
Table 5. Summary statistics of hydrochemical parameters of the surface water samples.
Table 5. Summary statistics of hydrochemical parameters of the surface water samples.
pHECCaMgNaKClSO4HCO3WQIIWQI
Dam
Min7.4104088.1839.3680.000.81275.2578.00134.2055.3623.50
Max7.8180099.7045.49103.301.289124.2592.00201.3062.1827.80
Mean7.5134994.0442.7293.921.00790.3285.77173.2158.1525.46
SD0.14302.444.142.076.220.1413.744.9719.871.981.45
CV1.9022.424.404.856.6214.4015.215.7911.473.415.69
Oued Rboua
Min7.568088.1821.4893.700.90817.7575.00231.8050.8822.39
Max8.41230136.2745.44120.701.63853.2598.00372.1078.2236.22
Mean7.751010120.2437.67109.351.37135.5091.00307.2868.0530.93
SD0.44258.0721.9510.9712.380.3514.4910.7472.2511.946.21
CV5.6225.5518.2629.1111.3225.1940.8211.8023.5117.5520.09
Oued Timgad
Min7.11200108.2030.6080.000.81235.5086.00402.6069.4532.01
Max8.61500132.2647.84130.501.83571.00115.00591.7084.7541.26
Mean7.91326116.9337.49105.641.25745.18101.32500.5175.3036.51
SD0.49116.908.395.1415.020.3514.5610.9658.765.393.34
CV6.308.817.1713.7214.2228.0932.2210.8211.747.169.15
Wastewater
Min6.8101092.1827.8482.000.83051.5788.00597.8072.4738.53
Max7.61660128.3038.28133.501.815106.5098.001000.4095.2654.44
Mean7.11173107.8433.48101.531.3065.8792.27758.3882.0743.68
SD0.28185.5311.504.5119.740.3621.773.53116.186.114.59
CV3.9615.8210.6713.4819.4427.7133.063.8315.327.4410.52
Note(s): All parameters are expressed in mg/L while pH on scale and EC in µS/cm; WQI: water quality index for drinking purposes. IWQI: water quality index for irrigation purpose; Min: minimum; Max: maximumSD: standard deviation; CV: coefficient of variation (in %).
Table 6. Results of NSFWQI for water quality of stations.
Table 6. Results of NSFWQI for water quality of stations.
VariablesCaMgNaKClSO4HCO3
Weighting factor
Dam0.190.110.150.070.110.150.19
Oued Reboua0.190.110.150.070.110.150.19
Oued Timgad0.190.110.150.070.110.150.19
Wastewater0.190.110.150.070.110.150.19
Wi Ii Values
Dam13.318.2412.734.528.2412.7313.05
Oued Reboua13.068.5312.292.897.6111.1513.02
Oued Timgad13.588.9511.611.986.8110.3212.66
Wastewater10.086.327.431.035.359.2811.09
NSFWQI
Dam72.82
Oued Reboua68.55
Oued Timgad65.91
Wastewater50.58
Table 7. Tests of group mean quality for discriminant analysis.
Table 7. Tests of group mean quality for discriminant analysis.
VariablesWilks’ LambdaFdf1df2p-Level (Sig.)
pH0.5558.8083330.000
EC0.7733.2263330.035
Ca0.50210.9243330.000
Mg0.6495.9613330.002
Na0.8681.6743330.192
K0.8232.3613330.089
Cl0.38817.3583330.000
SO40.5867.7773330.000
HCO30.087116.0633330.000
WQI0.25033.0313330.000
IWQI0.19345.9143330.000
Table 8. Eigenvalues for the discriminant analysis.
Table 8. Eigenvalues for the discriminant analysis.
FunctionEigenvalue% of VarianceCumulative %Canonical Correlation
116.481 a77.277.20.971
24.324 a20.297.40.901
30.553 a2.61000.597
Note(s): a First 3 canonical discriminant functions were used in the analysis.
Table 9. Wilks’ Lamda and Chi-square test for the discriminant analysis.
Table 9. Wilks’ Lamda and Chi-square test for the discriminant analysis.
Test of Function(s)Wilks’ LambdaChi-Squaredfp-Level (Sig.)
1 through 30.007156.660150.000
2 through 30.12166.53580.000
30.64413.85930.003
Table 10. Standardized canonical discriminant function coefficients.
Table 10. Standardized canonical discriminant function coefficients.
VariablesFunction
123
pH0.4320.5920.308
K−0.4030.668−1.023
Cl0.723−0.9370.536
SO40.3050.6500.995
HCO3−1.057−0.2720.136
Table 11. The structure matrix for the discriminant analysis.
Table 11. The structure matrix for the discriminant analysis.
VariablesFunction
123
HCO3−0.791 *−0.1570.497
IWQI b−0.529 *−0.0610.346
Cl0.156−0.515 *0.244
pH0.1060.366 *0.252
EC b−0.039−0.110 *−0.105
SO4−0.1060.2910.529 *
WQI b−0.370−0.0420.472 *
Ca b0.0720.1720.363 *
Na b−0.102−0.012−0.199 *
K−0.0950.103−0.193 *
Mg b−0.0130.0270.117 *
Note(s): Pooled within-groups correlations between discriminating variables and standardized canonical discriminant functions; variables ordered by absolute size of correlation within function. * Largest absolute correlation between each variable and any discriminant function; b this variable not used in the analysis.
Table 12. The canonical discriminant function coefficients.
Table 12. The canonical discriminant function coefficients.
VariablesFunction
123
pH1.2371.6970.881
K−1.3122.177−3.334
Cl0.043−0.0560.032
SO40.0400.0850.130
HCO3−0.014−0.0040.002
(Constant)−7.777−18.124−17.580
Note(s): Unstandardized coefficients.
Table 13. The classification function coefficients.
Table 13. The classification function coefficients.
VariablesStation
DamOued RbouaOued TimgadWastewater
pH114.003114.213113.702101.158
K15.78036.53929.46128.856
Cl0.7570.2850.3190.342
SO42.8162.7612.9832.370
HCO3−0.158−0.117−0.089−0.019
(Constant)−580.199−581.729−602.609−493.412
Note(s): Fisher’s linear discriminant functions.
Table 14. Classification results a,c.
Table 14. Classification results a,c.
StationPredicted Group MembershipTotal
DamOued RbouaOued TimgadWastewater
OriginalCountDam1100011
Oued Rboua04004
Oued Timgad0110011
Wastewater0001111
%Dam100000100
Oued Rboua010000100
Oued Timgad09.190.90100
Wastewater000100100
Cross-validated bCountDam1100011
Oued Rboua03104
Oued Timgad0110011
Wastewater0001111
%Dam100000100
Oued Rboua075250100
Oued Timgad09.190.90100
Wastewater000100100
Note(s): a 97.3% of original grouped cases correctly classified. b Cross validation is performed only for those cases in the analysis. In cross validation, each case is classified by the functions derived from all cases other than that case. c A total of 94.6% of cross-validated grouped cases correctly classified.
Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to people or property resulting from any ideas, methods, instructions or products referred to in the content.

Share and Cite

MDPI and ACS Style

Mammeri, A.; Tiri, A.; Belkhiri, L.; Salhi, H.; Brella, D.; Lakouas, E.; Tahraoui, H.; Amrane, A.; Mouni, L. Assessment of Surface Water Quality Using Water Quality Index and Discriminant Analysis Method. Water 2023, 15, 680. https://doi.org/10.3390/w15040680

AMA Style

Mammeri A, Tiri A, Belkhiri L, Salhi H, Brella D, Lakouas E, Tahraoui H, Amrane A, Mouni L. Assessment of Surface Water Quality Using Water Quality Index and Discriminant Analysis Method. Water. 2023; 15(4):680. https://doi.org/10.3390/w15040680

Chicago/Turabian Style

Mammeri, Asma, Ammar Tiri, Lazhar Belkhiri, Hichem Salhi, Djouhaina Brella, Elhadj Lakouas, Hichem Tahraoui, Abdeltif Amrane, and Lotfi Mouni. 2023. "Assessment of Surface Water Quality Using Water Quality Index and Discriminant Analysis Method" Water 15, no. 4: 680. https://doi.org/10.3390/w15040680

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop