Next Article in Journal
Analysis of Heavy Metal Contamination in Macroalgae from Surface Waters in Djelfa, Algeria
Previous Article in Journal
Impact of Antibiotic Pollution on the Bacterial Population within Surface Water with Special Focus on Mountain Rivers
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

A New Cross-Flow Type Turbine for Ultra-Low Head in Streams and Channels

1
Department of Civil, Energy, Environmental and Material Engineering (DICEAM), University Mediterranea of Reggio Calabria, 89124 Reggio Calabria, Italy
2
Department of Engineering, University of Palermo, 90128 Palermo, Italy
*
Author to whom correspondence should be addressed.
Water 2023, 15(5), 973; https://doi.org/10.3390/w15050973
Submission received: 18 January 2023 / Revised: 22 February 2023 / Accepted: 28 February 2023 / Published: 3 March 2023
(This article belongs to the Special Issue Recent Advances in Hydraulic Turbines)

Abstract

:
In the last few decades, hydropower production has been moving toward a new paradigm of low and diffused power density production of energy with small and mini-hydro plants, which usually do not require significant water storage. In the case of nominal power lower than 20 kW and ultra-low head H (H < 5 m), Archimedes screw or Kaplan type turbines are usually chosen due to their efficiency, which is higher than 0.85. A new cross-flow type turbine called Ultra-low Power Recovery System (UL-PRS) is proposed and its geometry and design criteria are validated in a wide range of operating conditions through 2D numerical analysis computed using the ANSYS Fluent solver. The new proposed solution is much simpler than the previously mentioned competitors; its outlet flow has a horizontal direction and attains similar efficiency. The costs of the UL-PRS turbine are compared with the costs of one Kaplan and one cross-flow turbine (CFT) in the case study of the main water treatment plant of the city of Palermo in Italy. In this case, the UL-PRS efficiency is estimated using a URANS 3D numerical analysis computed with the CFX solver.

1. Introduction

Hydropower plants are traditionally classified, according to the nominal power P of the turbine, into large (P > 100 MW), medium (100 MW > P > 15 MW), small (15 MW > P > 1 MW), mini (1 MW > P > 100 kW) and micro (100 kW > P > 5 kW) hydro plants [1]. In the last few decades, small and mini new hydro plants have mainly been constructed. This is also due to the search for low, diffused power density production of energy, but the main reason is that medium and large hydro plants are usually associated with water storage in large artificial reservoirs. The construction of new water reservoirs is often blamed for a bad environmental impact, mainly due to the induced reduction of solid transport [2], as well as the change occurring in the downstream river hydrological regime [3,4] and loss of water due to evaporation [5].
Small and mini hydro-plants do not require significant water storage upstream of the turbine. These types of hydro-plants can work with both action and reaction turbines. Action turbines with free discharge, such as Pelton or cross-flow ones, are usually simpler and allow a short payback time, even with a small available nominal power. Turbines with a pressurized diffuser and positive outflow pressure, such as Francis and Kaplan ones, are more expensive but allow use of the entire available hydraulic jump, whereas turbines with free discharge need to leave the height between the horizontal axis of the turbine and the downstream water level unexploited (see Figure 1). This distance is usually small with respect to the total jump but can become significant with low and ultra-low head jumps. In this range, the kinetic energy of part of the flow of tidal currents can be converted into electricity by using kinetic turbines, where a converging duct is applied before the turbine to increase the total amount of intercepted energy. In this case, it is possible to compare the efficiency of different devices using the power coefficient defined in [6].
Other suitable locations for low head turbines are small weirs or natural/artificial bed jumps available in small channels, where the entire flow rate can be turbined. In this case, some authors have proposed variants of Francis and Kaplan type turbines, such as a siphon hydro turbine [7] and a hydraulic propeller turbine [8], but at the present time, these solutions have complex geometries and their cost could not be competitive in micro hydro plants.
The Power Recovery System (PRS) is a cross-flow type turbine with positive outflow pressure [9,10,11,12,13]. Cross-flow and PRS turbines have been tested and applied, up to now, mainly to hydropower plants with medium head jumps greater than 15 m and smaller than 100 m. For higher heads, a new cross-flow type turbine called H-PRS has also been proposed [14] to fill a technological void that exists at the present time for hydropower production inside pipes, where large head drops and small discharges are available, especially if the discharge has large temporal variability. For lower head jumps, Kaplan type turbines attain efficiency higher than 85% and are traditionally assumed to be the most efficient ones. In the following, we will show that it is also possible to achieve similar efficiency with a new PRS type turbine, named UL-PRS. The advantage of using PRS type turbines is that they have simpler geometry and their cost could be, for the same nominal power, much lower than the cost of Kaplan turbines.
In the following sections, after a short review of the PRS turbine design criteria, the UL-PRS turbine is proposed and a sensitivity analysis of its efficiency with respect to the head jump is carried out. Finally, a UL-PRS prototype is designed for a potential site in the main wastewater treatment plant (WWTP) of the city of Palermo. The same cost/benefit analysis is applied to the selected case study for the UL-PRS and for other possible competitors [15].

2. PRS Turbine Design for Ultra-Low Hydraulic Heads

PRS is an inline turbine with a mobile flap for hydraulic regulation, a pressurized diffuser and the same runner as the cross-flow turbine (Figure 2). The design procedure for the PRS can be divided into two steps. The first step is the design of the runner, i.e., rotational velocity ω, diameter D, width W, blade thickness t and number of blades Nb. The second step is the stator design, i.e., nozzle and diffuser.
In the case of an ultra-low hydraulic head, i.e., ΔH ≤ 3 m [7], the traditional PRS diffuser still provides good efficiency values but has a vertical outlet flow and shows a sharp efficiency reduction close to the minimum head values. See in Figure 3 the efficiencies computed with several PRS machines designed using different head values, but the same flow rate (Q = 0.840 m3/s), the same velocity ratio (Vr = 1.8) and the same rotor outer diameter (D = 913 mm). The efficiencies are defined as follows [14]:
η = P γ · Q · Δ H
where P is the produced mechanical power, γ is the water specific weight, ΔH is the difference between the Total Energy Level (T.E.L.) of the inlet channel and the T.E.L. of the discharge channel (Figure 4). T.E.L. is the entire energy per unit weight of the flow, obtained as the sum of the piezometric level and the kinetic energy terms.
The reason for the sharp efficiency reduction is likely to be that the pressure differences inside the rotor of a cross-flow type turbine are usually small with respect to the kinetic energy resulting from the energy transformation inside the nozzle but become significant in the case of low ΔH. In this case, the angle of the flow direction with respect to the gravity force direction became quite important in the machine design. For this reason, this paper presents a new cross-flow type turbine, named UL-PRS (Figure 4), equipped with a new diffuser that makes it possible to keep the hydraulic efficiency above 80%, even with a hydraulic head drop of a few hundred millimeters and has a horizontal outflow direction (see Figure 4).
The UL-PRS design can be divided into two steps. The first is the design of the rotor and nozzle of the UL-PRS turbine, which is basically the same as the previous PRS and is fully described in [9,10,11,12,13].
The second step is the design of the pressure diffuser, which is composed of three parts. The first part (I in Figure 5) was designed according to the following hypothesis (see Figure 6): the runner outlet velocity only has radial component V2, which is constant along all the runner outlet circus; the velocity component on the direction normal to any radius of the runner normal to the axis is constant inside part I [16] and its module is equal to V2; the two lateral walls are planar and their distance is equal to W, the width of the runner. According to these hypotheses, the flux V2 per unit rotor outlet area can be obtained from the mass conservation equation as follows:
V 2 = 2 Q W · D · λ m a x
The radial distance r of the profile of the external wall of the diffuser from the axis of the rotor is a function of the λ angle and equal to:
r λ = D 2 1 + λ
and the maximum height Smax of the diffuser cross-section in part I is equal (Figure 6):
S m a x = D 2 λ m a x
In the second part of the diffuser (II in Figure 5), the height of the rectangular cross-section decreases to prevent the generation of vortices because of path curvature changes. The width of this part remains constant and is equal to W. The final cross-section is vertical, its height is set equal to R (Figure 7) and the tangent at the final point of the two profiles is horizontal.
The curvatures of the inner and outer profiles are constant and their values are computed from the known position of the initial and final points and of the corresponding tangent directions.
The last part of the diffuser, marked as III in Figure 5, is a straight divergent duct with a fixed height equal to R (Figure 8). The axial velocity component in a generic cross-section is assumed to change linearly, with a corresponding hyperbolic growth of the cross-section area [17], according to:
V l = V 0 + k   l
where V0 is the initial velocity and l is the distance of the section from the beginning of part III. The distance of the last cross-section, lmax, is about 4 times R, a good compromise between the need to prevent the generation of vortices and to contain the overall length of the diffuser.
The value of k in (5) and the maximum width Wout (Figure 8) are obtained by setting as Vout, the velocity of fluid particles at the exit of this last part of the diffuser, equal to 1 m/s, in order to get negligible final kinetic energy.
V o u t = 1   m / s  
k = V o u t V 0 l m a x
W o u t = Q V o u t   R

CFD Analysis of UL-PRS Turbine

We tested the new design procedure using both 2D and 3D computational fluid dynamics (CFD), the former of which compared the behavior of many different geometries. Due to the planar symmetry of its runner and distributor, the difference between the 2D and 3D solutions of a PRS turbine is usually small [16]. Although the efficiency calculated with 2D models is higher than the efficiency obtained with both 3D models and experimental data, this difference does not affect the optimality of the 2D parameters because the reduction of efficiency is not dependent on their setting and the optimal configuration is the same for both models [13]. The 2D analyses are much faster than the 3D ones, so we preferred to use the 2D approach for the research of optimal design and to limit the use of 3D analyses only to estimate the efficiency of the final geometry in a specific case study.
The numerical model was solved using ANSYS® CFX in the case of 3D domains and ANSYS® Fluent in 2D analyses. Following the experience of previous studies [12,13], the RNG k-epsilon model was selected as the turbulence model, combined with a scalable wall function [14]. For the study of rotating machines, both ANSYS® CFD solvers adopt a sliding mesh strategy, where the runner and its swept zone are discretized within a rotating reference system.
Fluent gives the option of selecting one among different approaches for pressure-based solving; we used the coupled one, where the whole set of momentum and continuity equations is solved simultaneously, resulting in strong coupling between pressure and velocity [18].
In CFX as the advection model, we chose the high-resolution scheme, which uses second-order differencing for the advection terms in flow regions with low variable gradients and uses the first-order advection terms only in areas where the gradients change sharply to prevent overshoots and undershoots and maintain robustness [14].
The effects of gravity are usually small with respect to the total jump in the traditional PRS but can become significant with low and ultra-low head jumps. For this reason, in both models, we enabled the gravity option under Gravity in Fluent or Buoyancy modes in CFX. When these settings are enabled, the solver increases the value of pressure p′ up to the following value:
p = p + ρ ρ 0 g y
where g is the norm of the gravitational acceleration, directed along the opposite direction of the vertical axis y in both models (Figure 9) and equal to 9.80665 m/s2, ρ is the density of the water, ρ0 is the operating density and equal to 1.225 kg/m3, the density of air at 15 °C.
The boundary conditions (BCs) selected in both 2D and 3D simulations are as follows: the total pressure, equal to the sum of the piezometric level and the kinetic energy terms per unit weight, at both the nozzle inlet and the outlet section of the casing for the static domain; module and direction of the angular velocity vector for the runner domain. All analyses were run for a simulation time corresponding to more than 6 full revolutions [16] and more than 200 time-steps per revolution in order to guarantee periodic, deterministic convergence of the model [14]. Previous studies have shown a very good match between the results of this numerical model and the experimental data [10,11]. A preliminary grid convergence analysis, aimed at assessing the minimum density of the mesh required to get a negligible numerical error, has been carried out using steady state simulations and a maximum root mean square residual equal to 10−5 [13,14].
In Table 1, the parameters of the convergence meshes used in both the 2D and 3D simulations are shown. Figure 9 shows the 3D mesh for UL-PRS 1.
A series of CFD 2D simulations were then performed. The geometrical parameters of the two different UL-PRS turbines are shown in Table 2. Both turbines were solved assuming the same flow rate Q, but the rotational velocity and width W were changed in each simulation to maintain the optimality conditions according to the different possible heads ΔH. The optimality conditions and the corresponding design criteria can be found in [9,10,11,12,13]. Observe that the blade maximum thickness tmax in the last row is selected according to [13] to guarantee structural safety and maintain high hydraulic efficiency.
The resulting efficiencies η versus heads ΔH are shown in Figure 10 along with the same values η ¯ normalized with respect to the maximum efficiency computed for each different geometry.
η ¯ = η η m a x
Because we used 2D models, we expect the computed efficiencies to be higher than the efficiencies computed with 3D models or obtained from experimental data, but we can rely much more on the normalized values, also according to previous analyses [13]. We can observe an abrupt reduction in the normalized efficiencies for both turbines only for head drops lower than 0.5 m. The reason for such a reduction is likely to be that the kinetic energy at the rotor inlet becomes very small for extremely low water heads and is strongly dependent on the elevation of the single inlet point, in contrast with the design hypothesis. See in Table 3 a list of the efficiencies computed for both the PRS machines, shown in Figure 3, and the UL-PRS1 one, shown in Figure 10. All turbines are designed for the same flow rate (Q = 0.840 m3/s), velocity ratio (Vr = 1.8) and outer runner diameter (D = 913 mm) and differ only for the nozzle axis orientation and the shape of the diffuser. The comparison clearly shows some advantages for the efficiencies of the UL-PRS turbine, mainly with head jumps lower than 3 m.

3. Case Study: Acqua Dei Corsari WWTP

The main wastewater treatment plant in the city of Palermo is the Acqua dei Corsari plant, located at the southeast end of the city (Figure 11). The WWTP is at an average altitude of 10 m above sea level and covers an area of approximately 110,000 m2.
At present, the treated discharge Q is about 0.8 m3/s, corresponding to the wastewater produced by 320,000 equivalent inhabitants (EinH), and is expected to increase to 1.0 m3/s in two years, equal to the wastewater produced by about 400,000 EinH. A small head jump h1 of about 3.5 m is present at the end of the disinfection channel (red area in Figure 11). The clarified water flow passes through two rectangular weirs and reaches the discharge channel. In the case of heavy rain events, part of the water at the entrance of the plant bypasses sewage treatment and reaches the same discharge channel. The water manager, AMAP S.p.A., is willing to recover the energy from this head jump by installing a hydraulic turbine to reduce the energy costs linked to the treatment processes.

UL-PRS Turbine Solution

The design parameters chosen for the UL-PRS are a flow rate and a head drop, respectively, equal to 0.840 m3/s and 3.75 m. The available hydraulic jump ΔH = 3.75 m is given by the difference between the Total Energy Level T.E.L.1 of the inlet channel (with respect to the bed of the discharge channel) and the T.E.L.2 of the discharge channel, minus about 0.2 m of head losses ΔHls, estimated in the suction pipe and in the butterfly valve, respectively, marked with 3 and 4 in Figure 12. Following the design criteria discussed in [9,10,11,12,13], a diameter D and width W equal to 913 mm and 609 mm are selected, respectively, for a rotational velocity ω equal to 75 rpm. The UL-PRS turbine (marked with 6 in Figure 12) is installed in a specific underground room downstream of the plant channel. In the case of overflow, part of the water bypasses the turbine and reaches the discharge channel through the original rectangular weirs (green dashed arrows). In the case of maintenance work of the turbine, it is possible to cut off the turbine and restore the actual layout of the WWTP just by closing the butterfly valve and the gate valve, marked with numbers 4 and 7, respectively.
The iron pipe, with a circular section of diameter Dpipe equal to DN700, is connected to the rectangular inlet section of the nozzle of the turbine through a special convergent. 3D numerical analysis has been carried out for validation by computing the efficiency and the flow rate of the turbine for a given head drop ΔH. The turbine shows an efficiency equal to 80.8%, with a mass flow rate close to the design data (Q = 806 m3 s−1; ΔH = 3.75 m; ω = 75 rpm; α = 15°; λmax = 100°; D = 913 mm; W = 609 mm).
A comparison between the velocity fields in the symmetry plane of the 3D simulation (Figure 13a) and the 2D simulation (Figure 13b) shows a good match for the accuracy required by the proposed UL-PRS design approach, except for the last part of the diffuser, whose width increases with a hyperbolic law in the 3D model, whereas it is constant in the 2D analysis.
Figure 14a,b show the head field, respectively, in the symmetry plane of the 3D simulation and the 2D one. From this comparison, similar conclusions can be derived.
See in Figure 15 and Figure 16 3D views of the 3D solution.

4. Cost/Benefit Analysis

An economic analysis is necessary to evaluate whether the new UL-PRS scheme should be chosen as an alternative to other possible schemes of hydropower systems. These schemes are compared on the basis of the expected costs and benefits during the lifespan of the turbine by means of economic criteria. Economic analysis strongly depends on the accuracy of the estimated costs and benefits. These estimations are not always easy to obtain, especially when some of the sought-after characteristics are only preliminarily defined.
The benefit for investors is savings in terms of self-produced energy or annual income from the sale of energy production. This benefit depends on the amount of energy produced during the lifespan of the turbine and on the specific conditions of the energy market.
It is useful to split the costs into the following main groups, as described below:
  • Civil work costs: costs for the required modification of the existing infrastructure (black solid, thick lines in Figure 12). These costs include the excavation and building of a specific underground room downstream of the plant channel for turbine housing.
  • Hydropower system costs: these include the cost of the turbine, the gearbox, and the electrical generator of an asynchronous type (Figure 12). We estimated a cost of 13,000 EUR for both the gearbox and the electrical generator with a high number of polar couples. For the UL-PRS turbine realization, we estimated a cost of 2500 EUR/kW.
  • Control system and installation costs: these include the cost of the control system for the regulation and management of the turbine and the cost of installation. In the range of the investigated nominal electrical power (Pe < 20 kW), the control system cost can be expected to be equal to 40,000 EUR [15].
  • Operation and maintenance (O&M) costs: in the case of micro hydro plants, the literature suggests assuming a yearly cost in the range of 2.2% to 3% of the cost of investment Ci [19].
C O & M m i n = 2.2 %   C i   EUR / year  
C O & M m a x = 3.0 %   C i   EUR / year
Decommissioning costs are marginal compared to the other costs, also because part of these costs is compensated from recovery and sale of raw materials, such as copper, steel and other precious metals, present in the dismissing components. For this reason, they are neglected in the benefit/cost analysis.
In Table 4, we compare the UL-PRS solution with the installation of a commercial Kaplan Turbine and cross-flow turbine (CFT), assuming two possible different O&M annual costs (2.2% and 3.0% of Ci) [19]. For the evaluation of the Kaplan and CFT solution costs, we refer to [15].
For hydropower plants with nominal power up to 1 MW and produced energy up to 250 MWh/year, the Italian Regulatory Authority for Energy Networks and Environment (ARERA) sets a guaranteed minimum price pMWh for the sale of energy. This guaranteed minimum price pMWh is equal to 158.9 EUR /MWh for 2022 [20].
The total energy to be produced over a typical year and the corresponding average cash flows are calculated assuming the hydropower plant to be working 24 h per day and 350 or 330 days per year, respectively, in the case of O&M cost equal to CO&Mmin or CO&Mmax (Table 4). A single index well representing the global economic benefit of the plant is the payback period ny [years], given by the ratio between the cost of investment Ci [€] and the average cash flows Cf [€/year] of each solution in both cases of CO&Mmin or CO&Mmax.
C f = P e 1000 · 24   h · d a y s · p M W h C o & M EUR / year  
n y = C i C f   years
The UL-PRS plant is the solution with the shorter payback period (Table 4). Other indices to be taken into account for device selection are the risk of cavitation due to unexpected flow rates, as well as the constructive simplicity of the device and the corresponding low maintenance cost. A more detailed cost analysis could also explicitly account for the temporal variation in money value.
A summary of all the benefits of each solution is reported in Table 5.

5. Conclusions

For low head jumps, Kaplan type turbines attain efficiency higher than 85% and are traditionally assumed to be the most efficient ones, but the results shown in the present analysis suggest that the new UL-PRS type turbine could also be an attractive alternative solution. The main advantage of UL-PRS and CFT turbines is their constructive simplicity; moreover, their cost could be, for the same nominal power, much lower than the cost of Kaplan turbines. The pressurized outflow present in UL-PRS allows, in contrast to CFT turbines, exploitation of the entire available hydraulic jump, still saving a global efficiency greater than 80%.
UL-PRS turbines show an abrupt reduction in efficiencies for head drops lower than 0.5 m. Further research is still required in this head range to optimize the shape of the stator and the rotor when the velocity of the particles entering the rotor significantly changes from one point to another on the inlet surface.

Author Contributions

Conceptualization: M.S. and T.T.; Investigation and Data Curation: C.P. and L.G.; Software: C.P. and M.S.; Writing—Review & Editing: C.P., M.S. and L.G.; Formal Analysis: P.G.F.F.; Supervision: T.T. and P.G.F.F. All authors have read and agreed to the published version of the manuscript.

Funding

This research has been carried out as part of the contract n. 9794 of 09/09/2021 between the University Mediterranea of Reggio Calabria and the Regione Calabria, with the financial support of Regione Calabria.

Institutional Review Board Statement

Not applicable.

Informed Consent Statement

Not applicable.

Data Availability Statement

Not applicable.

Conflicts of Interest

The authors declare no conflict of interest.

Abbreviations

ARERAItalian Regulatory Authority for Energy, Networks and Environment
BCsBoundary conditions
CFDComputational Fluid Dynamics
CFTCross-flow Turbine
EinHEquivalent Inhabitants
H-PRSHigh Power Recovery System
PRSPower Recovery System
O&MOperation and Maintenance
T.E.L.Total Energy Level
UL-PRSUltra-low Power Recovery System
WWTPWastewater Treatment Plant

Symbols

Citotal cost (EUR)
Cfaverage cash flows (EUR/Year)
CO&Mminminimum operation and maintenance annual cost (EUR/Year)
CO&Mmaxmaximum operation and maintenance annual cost (EUR/Year)
Douter runner diameter (m)
Dpipediameter of the pipe (m)
ΔHspecific energy drop per unit weight (m)
gstandard acceleration due to gravity (m s–2)
kconstant in linear law of the velocity (s–1)
ldistance from the beginning of part III (m)
lmaxlength of part III of the diffuser (m)
Nbnumber of blades (–)
nypayback period (years)
Pproduced mechanical power of the turbine (W)
Penominal electrical power (kW)
ppressure plus the geodetic term (Pa)
p′value of pressure (Pa)
pMWhguaranteed minimum prices for the sale of energy (EUR/MWh)
Qmass flow rate (m3 s–1)
Router runner radius (m)
r(λ)radial distance r of the profile of the external wall of the diffuser from the axis of the rotor (m)
Smaxmaximum height of the diffuser in part I (m)
tblade thickness (m)
tmaxblade maximum thickness (m)
V(l)generic velocity of particles in part III (m s–1)
V0velocity at the beginning of part III (m s–1)
V2runner outlet velocity (m s–1)
Voutvelocity at the end of part III (m s–1)
Wrunner width (m)
W(l)generic width of part III of the diffuser (m)
Woutmaximum width of part III of the diffuser (m)
ygeodetic elevation respect the axis of the runner (m)
αabsolute velocity inlet angle (radians)
βrelative velocity inlet angle (radians)
γwater specific weight (N m–3)
ηhydraulic efficiency of the turbine (–)
η ¯ normalized hydraulic efficiency of the turbine (–)
λrunner inlet/outlet angle (radians)
λmaxmaximum runner angle (radians)
ρdensity of the water (kg m–3)
ρ0density of the air at 15 °C (kg m–3)
ωrunner rotational velocity (rad s–1)

References

  1. Damtew, Y.; Getenet, G. Assessment of Hydropower Potential of Selected Rivers in North Shoa Zone, Amhara Regional State, Ethiopia. Am. J. Energy Res. 2019, 7, 15–18. [Google Scholar] [CrossRef]
  2. Finger, D.; Schmid, M.; Wüest, A. Effects of upstream hydropower operation on riverine particle transport and turbidity in downstream lakes. Water Resour. Res. 2006, 42, W08429. [Google Scholar] [CrossRef] [Green Version]
  3. Kuriqi, A.; Pinheiro, A.N.; Sordo-Ward, A.; Garrote, L. Influence of hydrologically based environmental flow methods on flow alteration and energy production in a run-of-river hydropower plant. J. Clean. Prod. 2019, 232, 1028–1042. [Google Scholar] [CrossRef]
  4. Trussart, S.; Messier, D.; Roquet, V.; Aki, S. Hydropower projects: A review of most effective mitigation measures. Energy Policy 2002, 30, 1251–1259. [Google Scholar] [CrossRef]
  5. Scherer, L.; Pfister, S. Global water footprint assessment of hydropower. Renew. Energy 2016, 99, 711–720. [Google Scholar] [CrossRef]
  6. Li, Y. On the definition of the power coefficient of tidal current turbines and efficiency of tidal current turbine farms. Renew. Energy 2014, 68, 868–875. [Google Scholar] [CrossRef]
  7. Zhou, D.; Gui, J.; Deng, Z.D.; Chen, H.; Yu, Y.; Yu, A.; Yang, C. Development of an ultra-low head siphon hydro turbine using computational fluid dynamics. Energy 2019, 181, 43–50. [Google Scholar] [CrossRef]
  8. Guzmán-Avalos, P.; Molinero-Hernández, D.; Galván-González, S.; Herrera-Sandoval, N.; Solorio-Díaz, G.; Rubio-Maya, C. Numerical design and optimization of a hydraulic micro-turbine adapted to a wastewater treatment plant. Alex. Eng. J. 2023, 62, 555–565. [Google Scholar] [CrossRef]
  9. Sinagra, M.; Sammartano, V.; Morreale, G.; Tucciarelli, T. A New Device for Pressure Control and Energy Recovery in Water Distribution Networks. Water 2017, 9, 309. [Google Scholar] [CrossRef] [Green Version]
  10. Sinagra, M.; Aricò, C.; Tucciarelli, T.; Morreale, G. Experimental and numerical analysis of a backpressure Banki inline turbine for pressure regulation and energy production. Renew. Energy 2020, 149, 980–986. [Google Scholar] [CrossRef]
  11. Sinagra, M.; Aricò, C.; Tucciarelli, T.; Amato, P.; Fiorino, M. Coupled Electric and Hydraulic Control of a PRS Turbine in a Real Transport Water Network. Water 2019, 11, 1194. [Google Scholar] [CrossRef] [Green Version]
  12. Sammartano, V.; Sinagra, M.; Filianoti, P.; Tucciarelli, T. A Banki-Michell turbine for in-line hydropower systems. J. Hydraul. Res. 2017, 55, 686–694. [Google Scholar] [CrossRef]
  13. Sinagra, M.; Picone, C.; Aricò, C.; Pantano, A.; Tucciarelli, T.; Hannachi, M.; Driss, Z. Impeller Optimization in Crossflow Hydraulic Turbines. Water 2021, 13, 313. [Google Scholar] [CrossRef]
  14. Picone, C.; Sinagra, M.; Aricò, C.; Tucciarelli, T. Numerical analysis of a new cross-flow type hydraulic turbine for high head and low flow rate. Eng. Appl. Comput. Fluid Mech. 2021, 15, 1491–1507. [Google Scholar] [CrossRef]
  15. Sinagra, M.; Picone, C.; Picone, P.; Aricò, C.; Tucciarelli, T.; Ramos, H.M. Low-Head Hydropower for Energy Recovery in Wastewater System. Water 2022, 14, 1649. [Google Scholar] [CrossRef]
  16. Sammartano, V.; Aricò, C.; Carravetta, A.; Fecarotta, O.; Tucciarelli, T. Banki-Michell Optimal Design by Computational Fluid Dynamics Testing and Hydrodynamic Analysis. Energies 2013, 6, 2362–2385. [Google Scholar] [CrossRef]
  17. Picone, C. Recupero Energetico All’interno delle reti Acquedottistiche Mediante Microturbine Idrauliche. Ph.D. Thesis, Department of Engineering, Palermo University, Palermo, Italy, 2022. [Google Scholar]
  18. Aricò, C.; Sinagra, M.; Picone, C.; Tucciarelli, T. MAST-RT0 solution of the incompressible Navier–Stokes equations in 3D complex domains. Eng. Appl. Comput. Fluid Mech. 2021, 15, 53–93. [Google Scholar] [CrossRef]
  19. Alawadhi, G.; Almehiri, M.; Sakhrieh, A.; Alshwawra, A.; Al Asfar, J. Cost Analysis of Implementing In-Pipe Hydro Turbine in the United Arab EmiratesWater Network. Sustainability 2023, 15, 651. [Google Scholar] [CrossRef]
  20. Italian Regulatory Authority for Energy, Networks and Environment (ARERA). Prezzi Minimi Garantiti per L’anno 2022. Available online: https://www.arera.it/it/comunicati/22/220118.htm (accessed on 18 January 2022).
Figure 1. Typical installation of a traditional cross-flow turbine where T.E.L. both time is the total energy level in the upstream and downstream channels, and ΔH is the usable hydraulic jump, lower than the entire available one.
Figure 1. Typical installation of a traditional cross-flow turbine where T.E.L. both time is the total energy level in the upstream and downstream channels, and ΔH is the usable hydraulic jump, lower than the entire available one.
Water 15 00973 g001
Figure 2. PRS turbine for medium head jumps: (a) Section view of the turbine in a symmetry plan; (b) Side view of the rotor [9,13].
Figure 2. PRS turbine for medium head jumps: (a) Section view of the turbine in a symmetry plan; (b) Side view of the rotor [9,13].
Water 15 00973 g002
Figure 3. Efficiencies versus head jumps solved using 2D CFD analysis.
Figure 3. Efficiencies versus head jumps solved using 2D CFD analysis.
Water 15 00973 g003
Figure 4. Section view of the UL-PRS turbine in a symmetry plan: T.E.L. is the total energy level and ΔH is the gross available hydraulic jump.
Figure 4. Section view of the UL-PRS turbine in a symmetry plan: T.E.L. is the total energy level and ΔH is the gross available hydraulic jump.
Water 15 00973 g004
Figure 5. Section view of the diffuser, composed of parts marked I, II and III.
Figure 5. Section view of the diffuser, composed of parts marked I, II and III.
Water 15 00973 g005
Figure 6. Section view only of the first diffuser part.
Figure 6. Section view only of the first diffuser part.
Water 15 00973 g006
Figure 7. Section view of the second diffuser part.
Figure 7. Section view of the second diffuser part.
Water 15 00973 g007
Figure 8. Top view of the last section of the diffuser.
Figure 8. Top view of the last section of the diffuser.
Water 15 00973 g008
Figure 9. Trimetric view of the UL-PRS 1 3D Grid scheme.
Figure 9. Trimetric view of the UL-PRS 1 3D Grid scheme.
Water 15 00973 g009
Figure 10. Sensitivity analysis of UL-PRS efficiency with respect to head jump.
Figure 10. Sensitivity analysis of UL-PRS efficiency with respect to head jump.
Water 15 00973 g010
Figure 11. Acqua dei Corsari WWTP: Aerial view.
Figure 11. Acqua dei Corsari WWTP: Aerial view.
Water 15 00973 g011
Figure 12. (a) Section and (b) planimetric view of a UL-PRS type turbine plant, where: 1. Inlet channel; 2. Discharge channel; 3. Suction pipe; 4. Butterfly valve; 5. Underground room; 6. T Hydropower System (blue lines); 7. Gate valve. In thick solid lines, the modifications are proposed for the new solution.
Figure 12. (a) Section and (b) planimetric view of a UL-PRS type turbine plant, where: 1. Inlet channel; 2. Discharge channel; 3. Suction pipe; 4. Butterfly valve; 5. Underground room; 6. T Hydropower System (blue lines); 7. Gate valve. In thick solid lines, the modifications are proposed for the new solution.
Water 15 00973 g012
Figure 13. Velocity field of UL-PRS: (a) 3D and (b) 2D simulations.
Figure 13. Velocity field of UL-PRS: (a) 3D and (b) 2D simulations.
Water 15 00973 g013
Figure 14. T.E.L. of UL-PRS: (a) 3D and (b) 2D.
Figure 14. T.E.L. of UL-PRS: (a) 3D and (b) 2D.
Water 15 00973 g014
Figure 15. Velocity field of UL-PRS in 3D view.
Figure 15. Velocity field of UL-PRS in 3D view.
Water 15 00973 g015
Figure 16. Velocity field in a frontal view of UL-PRS.
Figure 16. Velocity field in a frontal view of UL-PRS.
Water 15 00973 g016
Table 1. UL-PRS 1 and UL-PRS 2 convergence mesh details.
Table 1. UL-PRS 1 and UL-PRS 2 convergence mesh details.
ParametersUL-PRS 1UL-PRS 2
Type of Domain2D3D2D
Stator Domain elements42,3378,885,63940,352
Rotor Domain elements151,89512,723,105101,627
Total elements194,23221,608,744141,979
Table 2. UL-PRS 1 and UL-PRS 2 parameters.
Table 2. UL-PRS 1 and UL-PRS 2 parameters.
ParametersUL-PRS 1UL-PRS 2
Flow rate Q [m3/s]0.840
D [mm]913652
Head ΔH [m]0.25–150.2–10
ω(ΔH) [rpm]19.4–15024.3–171.6
WH) [mm]2360–3053695–523
α [°]1515
β [°]28.228.2
λmax [°]100100
Nb [-]3335
tmax [mm]2215.7
ηmax [%]87.587.1
Table 3. Two-dimensional efficiency comparison between UL-PRS1 and PRS turbines for different head jumps.
Table 3. Two-dimensional efficiency comparison between UL-PRS1 and PRS turbines for different head jumps.
Head ΔH [m]UL-PRS 1PRS
7.5087.3%85.9%
5.0087.0%85.4%
3.7587.5%85.1%
3.0086.8%84.6%
2.0086.5%84.8%
1.0086.2%84.1%
0.5085.4%83.6%
0.2584.1%82.4%
0.2083.7%81.4%
0.1580.9%79.5%
Table 4. Comparison of economic indicators.
Table 4. Comparison of economic indicators.
ParametersUL-PRSKaplan *CFT *
Head ΔH [m]3.753.752.8
Flow rate Q [m3/s]0.8060.8370.820
Hydraulic Efficiency0.8080.8640.835
Gearbox/belts/generator
efficiency
0.8870.8870.887
Global efficiency0.7170.7660.741
Nominal Power (Pe) [kW]21.223.616.7
Civil works [€]20,00020,00020,000
Hydropower System [€]66,000165,00050,000
Control system and
installation [€]
40,00040,00040,000
Total cost (Ci) [€]126,000225,000110,000
Specific cost [€/kW]594395346587
O&M cost (CO&MminCO&Mmax) [€/year]2772–37804950–67502420–3300
Total producible energy [MWh]178.080–167.904198.240–186.912140.280–132.264
Average cash flows (Cf) [€/year]25,525–22,90026,550–22,95019,870–17,717
Payback period (ny) [year]4.9–5.58.5–9.85.5–6.2
* According to [15].
Table 5. Benefit comparison of solutions.
Table 5. Benefit comparison of solutions.
UL-PRSKaplan *CFT *
Entire available hydraulic jump
Risk of cavitation
Hydraulic Efficiency > 80%
Payback period
Nominal Power > 20 kW
Constructive simplicity of the turbine
* According to [15].
Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to people or property resulting from any ideas, methods, instructions or products referred to in the content.

Share and Cite

MDPI and ACS Style

Picone, C.; Sinagra, M.; Gurnari, L.; Tucciarelli, T.; Filianoti, P.G.F. A New Cross-Flow Type Turbine for Ultra-Low Head in Streams and Channels. Water 2023, 15, 973. https://doi.org/10.3390/w15050973

AMA Style

Picone C, Sinagra M, Gurnari L, Tucciarelli T, Filianoti PGF. A New Cross-Flow Type Turbine for Ultra-Low Head in Streams and Channels. Water. 2023; 15(5):973. https://doi.org/10.3390/w15050973

Chicago/Turabian Style

Picone, Calogero, Marco Sinagra, Luana Gurnari, Tullio Tucciarelli, and Pasquale G. F. Filianoti. 2023. "A New Cross-Flow Type Turbine for Ultra-Low Head in Streams and Channels" Water 15, no. 5: 973. https://doi.org/10.3390/w15050973

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop